Top 10 Best 30a Esc

Comes Pre-soldered with XT60 Connector and 3.5mm bullet plugs. 5v3A UBEC Very Efficient - ESC can power receiver and servos. LiPo 2 - 4s Cells, NiCdNiMH 5 - 12 Cells, 6.4V - 16.8V. Low Battery Protection, Overheat Protection, Startup Throttle Protection, Signal Loss Protection, and Abnormal Voltage Protection. Programmable - Programming Card or using Transmitter.

NOTE 1. Since 2020.07.05, this items was soldered with 3.5mm Female banana connectors, effectively avoid welding problems 2. We have set up the program, the ESC do not need additional program. Input voltage2-4 S BEC 5V 3A Working current 30A 40A Optional on my shop. Universal SimonK Firmware 30A40A ESC Brushless Speed Controller, super simple. Small size combined with light weight for easy installation. 30A40A is optional on my shop. Military standard capacitor of extreme low resistance increases the ability of prevention of unwanted RF noise during flying. Extreme low resistance PCB is helpful for getting a super current endurance capability.. Microprocessor uses separate voltage regulator IC, with good anti-jamming capability..

Strong current endurance Steady Input voltage 3S 4S 5S Lipo battery in Continuous current current 30A, max spoort to 40Ain 10s. Supported Protocols Analog Signals - Multishot, One shot 42, Oneshot125, Digital Signals - Dshot 150, 300, 600. Stable firmware BLheli_S 16.5 is designed for superior performance in multirotors, and uses hardware upgradable. Use top quality components Imported Japanese Toshiba MOSFETs and Japanese Murata Ceramic Capacitors.3oz High-TG PCB board significantly reduces electrical heat soak and improves system efficiency. Ultra-Small and Light footprint 2g weight 2614.5mm ESC with the Silicone Signal and Power Wires provides high heat-resistance and more flexibility.

Spektrum Smart 30-amp Lite ESC, SPMXAE30A. Target gender unisex.

CompatibilityThe combo pack used for RC glider quadcopter helicopter aircraft copter multi-copter.. MaterialMade of high quality metal and plastic, easy to install, performs well.. 2212 MotorKV 2200, RiM 0.033, battery 2-3Li-Po, max power 342W, test prop 7x37x4.. New 30A ESCThe esc with t plug and 3.5mm banana connectors, more convenient to use input voltage 2-3 cells Li-Po battery.. If you have any questions after receiving the product, please feel free to contact us, we will try our best to solve your problems.

A2212 1400kv Brushless Outrunner Motor with connector, 12A60s, fit for Battery 2-3 Li-Poly.. 30A ESC BEC output linear mode 5V, 2A,Number of battery sections 2-3S LiPo. With T plug and 3.5mm banana connectors,effectively avoid welding problems.. SG90 Servo, 4.8V-6V, 0.12 sec 60 deg 4.8 V.. Suitable for RC Glider Quadcopter Helicopter Aircraft Copter Multi-copter.. Package Included 1 X A2212 1400kv Brushless Motor 1 X 30A Brushless ES 2 X SG90 9G Servos 1 Pair 8060 Propellers and other mounting Accessories..

Super smooth, accurate and programmable throttle linearity and throttle response.. Over temperature protection ,low voltage cut off protection ,signal loss protection and so on.. Strong BEC output 2A5V continuous and peak to 3A.. Supporting high RPM motors and programmable by programming card and transmitter .. High efficiency with low resistance and low heat MOSFET and CPU.

Regardless the throttle stick position, the motor will not spin after battery connected.. Throttle Calibration Throttle range can be configured to provide best throttle linearity, fully compatible with all market available transmitters.. Brake Setting brake enabled brake disabled.. Battery Type Li-xxLi-ion or LiPo Ni-xxNiMh or NiCd.. Full Protection Features Low voltage cutoff protection Over-heat protection Throttle signal lost.

BATTERY CHARGE CONTROLLER Under Voltage Controller, The battery control module has automatic charging and automatic shutdown functions, suitable for storage batteries and lithium batteries. The parameters are adjustable and can be saved in the memory after power off.. VOLTAGE SETTING METHOD Over-Discharge Protection Storage Battery Module, S1 overvoltage charge stop voltage or load start voltage. In the normal mode, press the S1 button to display the current overvoltage value. Press and hold the S1 button until it flashes, then press the S1 and S2 buttons to adjust the overvoltage value.. AUTOMATIC CHARGING 10V-60V 30A Under Voltage Control Module, The battery will automatically charge and disconnect the load when the voltage is insufficient. The battery will discharge and connect to the load through voltage.. S2 UNDERVOLTAGE Battery Protection Module, Charging start voltage or load stop voltage. In normal mode, press the S2 button to display the current undervoltage value. Press and hold the S2 button until the display flashes, then press the S1 and S2 buttons to adjust the undervoltage value.. NOTE Battery Protection Controller, In the normal power mode, hold down the S1 and S2 buttons until the digital picture tube displays 888, and then successfully complete the original factory settings..

High-performance 32-bit microprocessor, compatible with various brushless motors.. High-power switch mode BEC with 5V6V 4A output, employ more electronic devices, such as receivers and servos.. Pre-installed XT60 connector for the battery and 3.5mm gold connectors for the motor, no soldering is required.. Power on protection, over-heat protection, low-voltage protection and lost-signal protection.. Programmable via the LCD Program Box or transmitter..