Top 10 Best 4 Way Pressure Clamps
of November 2024
1
Best Choice
Peachtree Woodworking Supply
Peachtree Woodworking Supply
Peachtree Woodworking Supply 2 Pack of 4 Way Pressure Clamps For Clamping Panels - Using Pressure From All Four Directions. Ideal For Woodworkers and Cabinet and Furniture Makers
10
Exceptional
View on Amazon
2
Best Value
Peachtree Woodworking Supply
Peachtree Woodworking Supply
2 Pack of 4 Way Pressure Clamps For Clamping Panels - Using Pressure From All Four Directions. Ideal For Woodworkers and Cabinet and Furniture Makers (2 four way pressure clamps)
9.9
Exceptional
View on Amazon
3
Deadwood Crafted Tools
Deadwood Crafted Tools
DCT 4-Way Pressure Release Clamp Wood Panel Corner Clamping System Woodworking Bracket Set For Stock up to 6 Inches
9.8
Exceptional
View on Amazon
4
BIG HORN
BIG HORN
Big Horn 19622 4-Way Panel Clamp
9.7
Exceptional
View on Amazon
5
Bessey
Bessey
BESSEY VAS-23+2K, 23 ft Variable Angle Strap Clamp with 4 Clips
9.6
Exceptional
View on Amazon
6
Bora
Bora
Bora 4-Piece Parallel Clamp Set 571550I,Orange
9.5
Excellent
View on Amazon
7
Bora
Bora
Bora 50" Parallel Clamp Set, 2 Pack of Woodworking Clamps with Rock-Solid, Even Pressure, 571150T
9.4
Excellent
View on Amazon
8
Rockler
Rockler
Rockler Mini Deluxe Panel Clamps, 2-Pack
9.3
Excellent
View on Amazon
9
PONY
PONY
PONY 4-Pack Cabinet Clamps, 8510 Cabinet Claw, Face Frame Clamps for Installing Cabinets, 440 lbs Load Limited
9.2
Excellent
View on Amazon
10
WOODRIVER
WOODRIVER
WoodRiver Clamping System
9.1
Excellent
View on Amazon
About 4 Way Pressure Clamps
Click here to learn more about these products.
Peachtree Woodworking Supply 2 Pack of 4 Way Pressure Clamps For Clamping Panels - Using Pressure From All Four Directions. Ideal For Woodworkers and Cabinet and Furniture Makers
Clamping Panels Can Certainly Be A Challenge. Especially When We Try To Use Everyday Pipe Clamps Or Bar Clamps. While These Types Of Clamps Work Fairly Well On Certain Glue Up Projects, The One Thing They DonT Do At All Is Apply Pressure From The Top And Bottom Of The Panels During Glue Up. In Fact, With All The Pressure Being Applied On Both Sides, Bar And Pipe Clamps Will Almost Certainly Bow, Buckle Or Rack Your Panel Glue Up Project. LetS Make Racked Panel Glue Ups A Thing Of The Past. With A Simple Turn Of The Rotating Clamp Handle, All Four Sides Of The Clamp Will Draw Inward At The Same Time. Build Any Length Clamp With The Durable Plastic Bars With 4 Notches For Maximum Adjustability To Handle A Variety Of Stock Widths. Clamp Can Be Used For Boards Up To 6 Inches In Thickness By Simply Adjusting The Clamp Width Capacity With The Appropriate Number Of Notches. Turn The Handle Clockwise To Tighten The Clamp And Turn The Handle Counter Clockwise To Release Pressure. The 4 Way Pressure Clamp Is Equipped With Side Pressure Pads To Prevent Damaging Your Stock. Now You Can Confidently Glue Up Wide Boards, Shelving, Table Tops, And More Up To 6 Thick. To Setup The Clamps Simply Attach The Clamp To Any Length 2 X 2S 2 X 4 Ripped In Half With The The Wood Screws That Are Provided, Apply Wood Glue To Your Project, Set The Clamps On To Your Panel Boards And Turn Handle To Tighten The Clamp On All Four Sides. We Recommend That You Place A 4 Way Pressure Clamp Every 12 To 18 For Best Results..
2 Pack of 4 Way Pressure Clamps For Clamping Panels - Using Pressure From All Four Directions. Ideal For Woodworkers and Cabinet and Furniture Makers (2 four way pressure clamps)
Clamping panels can certainly be a challenge. Especially when we try to use everyday pipe clamps or bar clamps. While these types of clamps work fairly well on certain glue up projects, the one thing they dont do at all is apply pressure from the top and bottom of the panels during glue up. In fact, with all the pressure being applied on both sides, bar and pipe clamps will almost certainly bow, buckle or rack your panel glue up project.. Lets make racked panel glue ups a thing of the past The uniquely designed 4 way pressure solves this age old issue by applying pressure to all four sides of your panel glue up. With a simple turn of the rotating clamp handle, all four sides of the clamp will draw inward at the same time. This provides equal pressure on to your panel and prevents bowing, buckling, or racked panels.. Build any length clamp with the durable plastic bars with 4 notches for maximum adjustability to handle a variety of stock widths. Clamp can be used for boards up to 6 inches in thickness by simply adjusting the clamp width capacity with the appropriate number of notches. Turn the handle clockwise to tighten the clamp and turn the handle counter clockwise to release pressure. The 4 way pressure clamp is equipped with side pressure pads to prevent damaging your stock.. Now you can confidently glue up wide boards, shelving, table tops, and more up to 6 thick. To setup the clamps simply attach the clamp to any length 2 x 2s 2 x 4 ripped in half with the the wood screws that are provided, apply wood glue to your project, set the clamps on to your panel boards and turn handle to tighten the clamp on all four sides. We recommend that you place a 4 way pressure clamp every 12 to 18 for best results.. This clamp package comes with two full 4 way pressure clamp assemblies. Includes 2 each rotating handle assemblies, 2 each tailstock assemblies, 4 each side pressure pads and 12 each 4 notch bars. Together, this setup will allow you to create two 4 way pressure clamps. More than one clamp is generally recommended for any project over 12 in length. Wood is required for setting up the clamp. Wood is NOT included..
DCT 4-Way Pressure Release Clamp Wood Panel Corner Clamping System Woodworking Bracket Set For Stock up to 6 Inches
LARGE PANEL GLUE-UPS The DCT 4-Way Pressure Release Clamp Wood Panel Corner Clamping System Woodworking Bracket Set handles stock up to 6 inches 15.2cm thick for simplifying the process of gluing table tops, countertops, furniture panels, cabinet doors, and more and saves you from using additional clamps to keep the glue-ups straight. 4-WAY Stock stays flat and prevents buckling of boards during glue-up because of the equally applied pressure from all four directions top, bottom, and both sides Ideal for gluing table tops, shelving, veneer, laminates Durable clamp only limited by the quality of prep and glue used. EASY TO USE Assembly instructions included More convenient than lining up standard clamps and cauls Attach notched bars to any length 1.5-inch x 1.75-inch 3.2cm x 4.4cm board equivalent to a 2x4 ripped in half with provided screws, set clamp and turn handle to tighten on large pieces, we recommend one clamp every 18 inches45.7cm for maximum clamping efficiency Make sure the 2x4s you use are not twisted Drill pilot holes for the outer-most screws when attaching the pressure pads. ADJUSTS TO YOUR PROJECT Build any length clamp with the durable plastic bars with 12 notches for maximum adjustability to handle a variety of stock widths Clamp can be used for boards up to 6 inches in thickness by simply adjusting the clamp width capacity with the appropriate number of notches Turn the handle to tighten the clamp and unwind the turn handle to release pressure Clamp has pressure pads to prevent damage to the edge of your stock. CONTENTS Package includes 2 12.75-inch long notch bars, 2 6.9-inch long notch bars, 1 clamp assembly head, 1 clamp assembly tail, 16 assembly screws 4x 38-inch, 12x 1-14-inch L, and assembly instructions 1 set with 1 clamp multiples needed for projects over approximately 2 feet61cm Wood required, not included.
Big Horn 19622 4-Way Panel Clamp
4-way action of panel clamp applies even pressure to glue joints. Will accept material from 12-inch to 3-12-inches thick of unlimited length. Use while gluing table tops, furniture panels and doors.
BESSEY VAS-23+2K, 23 ft Variable Angle Strap Clamp with 4 Clips
Strap Is Drawn For Both Sides Simultaneously Which Provides Evenly Distributed Clamping Pressure. Strap Coiling Mechanism Keeps Strap Neatly Contained. 4 Pivoting Corner Supports Are Included, Clamping Pressure Is Applied Evenly. Pressure Pads Pivot From 60 To 180 Degrees Making Clamping Simple Secure.
Bora 4-Piece Parallel Clamp Set 571550I,Orange
3.5-Inch Wide Padded Jaw Provides Constant, Even Pressure Without Damaging Material And The Jaw Stays In Place When Winding. 1,100Lbs 500Kg Of Clamping Pressure. Large, Easy-Grip Handle Makes It Easy To Lift And Slide Jaw Up And Down. Passive Lock Jaw Stays In Place While Winding Clamp.
Bora 50" Parallel Clamp Set, 2 Pack of Woodworking Clamps with Rock-Solid, Even Pressure, 571150T
Strong And Even 3.5-Inch-Wide Padded Jaw Provides Constant, Even Pressure Without Damaging Material And The Passive Lock Jaw Stays In Place When Winding The Clamp. Perfect Pressure Not Too Loose, Not Too Tight, Just Right With 1,100Lbs 500Kg Of Clamping Pressure. Rock-Solid Stability The Parallel Clamps Versatile Uses And Stability Will Help You To Deliver A Superior Finished Product You Can Be Proud Of. Easy-Grip Large Easy-Grip Handle Makes It Easy To Lift And Slide Jaw Up And Down.
Rockler Mini Deluxe Panel Clamps, 2-Pack
PONY 4-Pack Cabinet Clamps, 8510 Cabinet Claw, Face Frame Clamps for Installing Cabinets, 440 lbs Load Limited
PONY 8510 Cabinet ClawComplete your cabinetry projects in a fraction of the time with Pony cabinet claw. This unique and patented tool combines the various steps of face-frame cabinet installation into one easy process.. Dimensions Works on stiles from 1-12 inch to 2 inch Throat Depth 1-12 inch Minimum Opening 2 inch Maximum Opening Capacity 4-38 inch Jaw Width 2 Inch Jaw Width 2-716 inch. Max load capacity 440 lbs.. Pilot-Hole Drill There is a pilot-hole drilling guide on one end. The guide flips out of the way so you can drive screws to connect the cabinets without removing or repositioning the clamp.. Protection Pads Comes with 4 sets of protective rubber pads to cushion and protect cabinetry. Face frame stiles can be tightened, aligned, pre-drilled and fastened while the clamp remains in its original position.. ProfessionalProfessional, quality installation is achieved at a fraction of the time compared to the use of more conventional clamps..
WoodRiver Clamping System
Applies equal pressure on all four directions. Includes 2 clamps, 2 short bars, 2 long bars, screws. 2 x 4's not included. WoodRiver is proudly made by Woodcraft, Americas leading supplier of saws, planes, power tools, hand tools, wood stain and paint, routers, sanding, wood, kits, dust collection and more. Our award winning family of brands includes WoodRiver, Highpoint, Woodcraft and Woodcraft Magazine as well as the greatest selection of woodworking books, videos, and plans..