Top 10 Best 5/8 Fuel Line

Size ID 58inch 16mm,OD 0.94inch24mm.Material NBR.. Working Pressure 290psi. Burst Pressure 1160psi. Temperature Range -40F to 257F. Minimum Bend Radius 6.3inch160mm.. Applicable Medium 58 id fuel line can work with dieselbiodieselgasolineOilgreasewater and air,etc.. Application SAE 30R7 rubber fuel line widely used in fuel system, oil cooling, steam emission, PCV system, please check size and application pressure before purchase.. EVIL ENERGY provide this product 3-month warranty.Any problem you might have,please feel free to contact us via Amazon message..

ID 58 inch 16mm, OD 0.9 inch 23mm, 10 AN NBR liner hose, 10 feet. Use hose barbs and clamps, transfer of petroleum products fuel lines for small engines. Fuel Injection Hose Working Pressure 2Mpa. Burst Pressure 4Mpa, Handles temperature ranges of -40 to 275 degrees F. Push on lock hose designed for conveying gasoline, E-85, diesel, and bio-diesel fuels in cars, trucks, buses, etc. The Fuel Lines for fuel injected systems, are oil resistant,cold-resistant and ethanol tolerance.

-10 AN, Length 2 feet. ID size 58, 15.9mm OD size 2932, 22.9mm. Material Made by High-Graded Nitrile Rubber NBR with Textile Reinforced, Covered by Elastomer. Works With Push-On Hose End Fittings, suit 400 510 series hose ends. For use with Fuel System, E85, E10, Oils, Ethanol, Lubricants and Coolant System. Operation Temperature Ranges from -40 C degree to 100 C degree. Working Pressure Rating 280 PSI, Burst Pressure is 800 PSI..

CORROSION AND ABRASION RESISTANCEThis rubber line is made of high-quality nylon-reinforced CPE chlorinated polyethylene synthetic rubber on the inside provides constant flow during operation of the racing engine, along with woven stainless steel in the middle layer which achieves the desired flexibility and mechanical bond between the braiding layers. Full coverage outer braid of nylon, which is lightweight, yet extremely durable provides maximum corrosion and abrasion resistance.. MATCH WELL AND LEAKAGE FREE SEALWe provide a complete set, including 16.4 Ft fuel line and 10 pieces T6061 aluminum hose connector. Because they are all made in the same factory, there is no difference between tube and ends size, they can be matched well. This is an assembly, we provide a detailed instruction manual in the package to help you install it easily, but you must keep in mind that professional installation is highly required. Dont hesitate anymore, add to your cart now. POWERFUL COMPATIBILITY AND WIDELY USEDAN10 fuel line repair kit will fit most standard 58 inch tube stub in any fuel system. Works great as transmission line from your hard fuel line to fuel pump or from pump up to the fuel filter or carburetor. Compatible with most automotive replacement parts that fuels, coolants, and oils need be delivered, such as fuel pump, fuel filter, fuel tank, oil filter, oil sandwich adapter, turbo oil return and so on But please note Not for E85. MEET YOUR NEED, TIME AND MONEY SAVINGThis kit consists of 16.4 feet transfer hose and 10 swivel hose fittings. You want to use it as a replacement kit, that's a decent deal. This tube is long enough and can be cut to any size needed, and hose connectors have 4 different angles, you can choose the right hose end for your project. When you complete your project, it can keep your engine bay tidy. All connectors are made of T6061 aluminum can be reused with high strength and good durability.. RESPONSIBLE CUSTOMER SERVICEProfessional installation is highly recommended and use Adjustable AN Wrench will much better.SYKRSS is the responsible brand, always provide high-quality products and best service, and hope our users can get good shopping experiences..

Cover resists heat, oil, ozone and weathering. Spiral reinforced construction. Tube has been upgraded to meet changes in fuel characteristics and resists heat and oil. Convenient 2-ft. lengths in self-service, reusable, recyclable package that can be displayed on pegboard. Meets requirements of SAE J30R7 and DIN 73379 except for tolerances.

Nitrile tube that is spiral reinforced for enhanced durability. NBR-PVC cover that is oil resistant and resists the effects of high heat and ozone found in engine compartments. Vacuum rating of 24 inHg for sizes less than 12 in I.D., and 10 inHg for sizes 12 in to 34 in I.D. at ambient temperatures. Warning Do not use for pressure lines on fuel injected engines or for cooling system applications. Use an ACDelco Specialty Premium Fuel Injection Hose MPI for fuel injection applications. Intended for use with fuels where MTBE concentrations are no greater than 15 by volume.

100 brand new, never been used.. Stainless Steel innter hose CPE synthetic rubberThe middle layer 304 stainless steel wire mesh sleeve The outer layer 304 stainless steel wire. Braided Nylon innter hose CPE synthetic rubberThe middle layer 304 stainless steel wire mesh sleeveThe outer layer High quality braided nylon. Operating temperature -40 Degree F to 350 Degree F. Application forracing fuel,pump gas,fuels with ethanol,alcohol based fuels,motor oilcoolant etc..

APPLICATION- For racing fuel, pump gas, diesel, motor oil coolant etc. Nylon braided fuel hoses can be used as transmission oil cooler line, fuel return line, fuel supply line, coolant fluid hose, carburetor fuel hose, turbo cooler line, oil feed line, ls swap fuel line.. WORKING ENVIRONMENT-Maximum Working Pressure725psi5mpa. Bursting Pressure2465psi17mpa. Working Temperature Range-40 to 338-40 to 170.. SIZE- length10 feet3M. Inner diameter0.56 inches 14.2 mm. Outer diameter0.79 inches 20.10 mm.. MATERIAL- Inner layerCPE synthetic rubbermiddle layer304 stainless steel wire mesh sleeveouter layerbraided nylon. Resistant to high temperature pressure abrasion and aging. Excellent flexibility and flame retardancy.. NOTE- Double check the hose size before bidding. Our rubber hose is compatible with rubber fitting adapter. The fitting adapter for PTFE hose is NOT FIT.NOT FIT FOR E85..

HIGH-QUALITY MATERIAL - The high-pressure 10an hose covered with high quality is woven Nylon and 304 stainless steel braided CPE synthetic rubber to enhance flexibility and give a cool racing appearance.. NYLON BRAIDED - The 10an hose kit can stand -100 to 500 -73C to 260C, the maximum working pressure up to 500 PSI. The 916 fuel hose has good retardancy and excellent corrosion resistance. Best for the brake system, fuel pump, fuel filter, oil return, fuel return system, turbo cooler system, and transmission system, oil cooler kit, etc.. FLEXIBILITY - The highlight of this fuel line is its sublime pliability. Steel, aluminum, or plastic lines will not bend as easily as this tube. The superior bending ability of this fuel tube makes it easier to install. It also results in more fluidity in transmission.. WIDE APPLICATION - The 10an hose is specially designed to compatible with any fuel including methanol and nitromethane, oil, coolant, brake, transmission, clutch, diesel, hydraulic fluid, pump gas, and nitrous oxide. but NOT FIT E85.. CUT THE SIZE AS YOU WANT - The 10an line is 10 Feet 3 m, can be cut to size for all your applications. Our braided fuel line is also an excellent alternative to conventional fuel lines, the 916 hose can be applied to higher-intensity temperature and pressure environments. Oil resistant, cold-resistant, and ethanol tolerance.. Please note that the Hose Inner Diameter is 14.22mm 0.56 inch and the Hose Outside Diameter is 20.06mm 0.79 inch.

I.D. 58 or 15.9mm, odd. 3132 or 24.6mm, wt. C 25, max WP 50. Shields fire-alcohol fuel vent hose resists gasolinealcohol blended fuel and is Fire resistant. It features a weatherUV resistant NBRPVC cover. This hose primarily used for fuel vent lines gasoline up to 85 ethanol blended fuelsdiesel fuels. The temperature ranges from -20 Degree to 160 Degree. Meets USCG type A2 Requirements for pleasure boats. Meets Saej1527 type A2 ISO 7840 type A2 and NMMACE type accepted standards.