Top 10 Best 5v Relay Module

The module uses genuine quality relay, normally open interfaces , Maximum load AC 250V10A, DC 30V10A.. Using SMD optocoupler isolation, strong driving capability, stable performance trigger current 5mA.. Fault-tolerant design, even if the control line is broken, the relay will not move.. The interface design of human nature, all interfaces are available through a direct connection terminal leads, very convenient.. The Module can be set by jumper high or low trigger..

It is 4 Channel Isolated 5V 10A Relay Module, each relay can individually switch onoff by an opto-isolated digital input, Standard interface can be directly connected with microcontrollers and be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, DSP, etc., very convenient.. Equipped with high-current relay, maximum load AC250V 10A, 15A 125VAC, DC30V 10A Trigger current of opto-isolator 5mA.. RELIABLE Fault-tolerant design, even if the control line breaks, the relay will not move With optical coupling isolation, triggering more reliable, more stable.. EASY to INSTALL Equipped with screwed terminal plate and fixed bolt holesdiameter 3.1 mm on both sides for easy installation.. HighLow level trigger can be selected by jumper. Very versatile, you can reverse the input logic with the jumper..

1 Channel Relay Module- This Relay Board provides a single relay that can be controlled by any 5V digital output from your microcontroller.. Main Specification- Peak Load of NO Connector AC125250V10A, DC2830V10A Trigger Current 5mA 4pcs 3.1 mm Fixed Bolt Hole. Adopted SMD Optocoupler Isolation- The isolation circuit prevent damages to I O port by relay switch current.. Wide Application- These 5v relay board works well with ARM PIC AVR MCURaspberryCNC machine PS4 etc.. Humanization Design On Interfaces- All interfaces can be directly wired out through the terminals..

Driver Current15-20mA each. Indication LED's for Relay output status. IN can be high or low level control relay. Equiped with high-current relay, AC250V 10A DC30V 10A. Standard interface that can be controlled directly by microcontroller Compatible with , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic.

Microcontroller development board can be used as modules, can be used as appliance control. 5V - 12 V control signal of the TTL. Control DC or AC signals can control the 220V AC Load. There is a normally open and open normally closed contact. Useful to control a motor, a led strip, or any other module. How to use it Just connect a digital output of your board to your relay module, and you can control a power-demanding appliance with the digital signal.

5V 2-Channel Module Relay Board, Driver Current15-20mA each. Indication LED's for Relay output status. IN can be low level control relay. Equiped with high-current relay, AC250V 10A DC30V 10A. Standard interface that can be controlled directly by microcontroller Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic.

The relay can directly control a variety of equipment and loads, which meets international safety standards, and also has power and relay indicators.. This relay can be used not only as a microcontroller development board module, but also as a home appliance controller.. No need to buy the Jumper Wires extra, this set contains 20cm 10Pin female to female, female to male, male to male Dupont Jumper Wires, with which you can easier to complete the project..

Relay module this relay board supports high and low level trigger and can be controlled by any 5V digital output of the microcontroller. Parameter details maximum load of normally open interface AC 250v 10A, DC 30v 10A, trigger current is 5mA The 5v relay control board adopts SMD optocoupler isolation, which has strong driving ability and stable performance. Practical design with fault-tolerant design, the relay module will not operate even if the control line is disconnected All interfaces can be provided through directly connected terminal s since the humanized interface design, it is very convenient to use. High compatibility the relay module can be directly controlled by the 5V logic signal provided by the microcontroller, suitable for 8051, Raspberry Pi, PIC, DSP, ARM, AVR, MSP430, TTL logic, etc.. Wide application this 5V relay board can be applied with Raspberry CNC machine ARM PIC AVR MCU PS4 and more.

Name kits module. 5V relay module 1 way relay module. New 5V relay module. This product contains 5 modules. 100 brand new.

The Relay Board Maximum load AC 250V10A, DC 30V10ATrigger current of opto-isolator 5mA.. Using SMD optocoupler isolation, strong driving capability, stable performance.. The interface design of human nature, all interfaces are available through a direct connection terminal leads, very convenient.. Fault-tolerant design, even if the control line is broken, the relay will not move.. Wide Application,The relay board works well with ARM PIC AVR MCURaspberryCNC machine PS4 etc..