Top 10 Best Anycubic Wash And Cure Station

7 Light Transmittance Fast Printing The screen light transmittance of AnyCubic Photon Mono 4K reaches an industry-leading 7, helping faster printing curing speed, single-layer exposure curing time as low as 1.5s, and printing speed up to 50mm h, which saves half the time compared to other ordinary resin 3d printers, allowing you to get the model faster.. 4K High Resolution This resin printer features a 4K monochrome LCD screen. The 3840 x 2400 high-definition resolution prints sharper and more detailed models.The Photon Mono 4K printer adopts a high-contrast monochrome screen of more than 3501, so that the image in the exposed area shows clear details and brings you higher printing quality.. 6.23 LCD Screen ANYCUBIC Photon Mono 4K printer is equipped with a 6.23 inches screen with a maximum print volume of 6.5x5.2x3.1 inches. The monochrome screen lasts 4X longer than the RGB LCD screen, and a replaceable scratch-resistant film and an additional protective film is installed on the LCD screen to effectively protect the screen.. Adjustable Power The UV lamp power adjustment range is 30-100, not only supports ordinary 405nm UV resin, but also supports special resins, making it compatible with more materials and environments to meet more of your printing needs. Proper adjustment of optical power can significantly extend the life of screens and lights.. Free Use of Professional Software We provide you with the self-developed professional slicing software AnyCubic Photon Workshop for free. You can freely enjoy the fun of 3D printing on AnyCubic Photon Mono 4K without worrying about the fee of the software..

Newest Upgraded and More Convenient Newest Wash and Cure machine added lens to UV lamp beads, the light source intensity distribution is more uniform, and the surface of the model is smoother. With the 360 automatic rotating curing table and added bottom reflector, the bottom curing has no dead ends, so that the entire model is cured more thoroughly. 2-In-1 Wash and Cure Station Dual functions of cleaning and curing can not only remove most of the chemicals, settle scrubbing and mess issues, but also seriously streamline the whole post-processing. It's a professional solution to the messy clean up job of your fabulous prints and also helps reduce the clutter on your desk. 1-60min time adjustable, customize knob cleaning and curing time. Each layer of the 3D printer model can be better cleaned and cured according to your DIY needs. Widely Compatibility The ANYCUBIC wash and cure machine is a great addition to most type of regular resin printer, Compatible with most LCDDLPSLA 3D printers such as QIDI Shadow, NOVA, Mars series and other regular resin printers with similar build volume size as it does for photon series, this Wash Cure machine has opened up a whole new world of 3d printing for you and greatly enhance your workflow. Effective and Diverse Washing Modes There is a propeller in the bottom of wash cure station, when work, it spins the solution like a little tornado and changes spin direction halfway through the wash , which creates the perfect flow to clean every inch of the print. 2 modes of Cleaning 1. Basket washing, Remove the model and put it into the basket for direct cleaning 2. Suspension washing, Directly hang the print platform on the basket or cleaning stand to clean, reducing exposure to resin. Anti-UV Light Hood The transparent cover of this wash cure machine can block up to 99.95 of ultraviolet rays with a wavelength of 405nm, thus able to be effective in high resin solidification rate and this wash and curing box adopts sealed cleaning, which effectively prevents the cleaning agent from splashing and volatilization, and provides more safety..

2-in-1 Multifunctional Design The machine has dual functions of cleaning and curing. It makes it easier to clean and cure the printed model. It is an excellent assistant for UV LCD 3D printers. A dual-purpose machine to save more space and keep the working area clean.. Cleaning Mode 1. Basket cleaning remove the model and put it into the basket for direct cleaning 2. Hanging cleaning directly hang the print platform on the cleaning basket or cleaning stand to clean, reducing exposure to resin. Compatible with most LCDDLPSLA 3D printers such as Mars series, Photon series, etc. on the market.. Anti-UV Light Hood One-piece molding hood, 99.95 blocking rate of 405nm wavelength UV light. The resin cleaning and curing station adopts sealed cleaning, which effectively prevents the cleaning agent from splashing and volatilization, and provides more security.. UV Lamp Beads Upgrade Curing Mode lamp beads add lenses, the light source intensity distribution is more uniform, and the surface of the model is smoother. With the 360 automatic rotating curing table, the bottom reflector is added, the bottom curing has no dead corners, so that the entire model is cured more thoroughly.. Custom Time Adjustment 1-60min time adjustable, knob custom cleaning and curing time. Each layer of the 3D printer model can be better cleaned and cured according to your DIY needs. After cleaning and curing the model, the performance is significantly improved, helping you create a perfect model..

ANYCUBIC Resin 3D Printer, Photon Mono 4K 6.23 Monochrome UV LCD 3D Printer Fast Printing, Power Adjustable, 5.19L x3.14W x6.49H Printing Size. ANYCUBIC 3D Printer Resin, 405nm SLA UV-Curing Resin with High Precision and Quick Curing Excellent Fluidity for LCD 3D Printing Black, 500g. ANYCUBIC Wash and Cure Station, Newest Upgraded 2 in 1 Wash and Cure 2.0 Machine for Mars Anycubic Photon S Photon Mono LCD SLA DLP 3D Printer Models UV Rotary Curing Resin Box.

, Anycubic AirPure, with a compact body of 4.5 x 1.8 x 1.8 inches, is less than the size of a small 250ml of coke. It can be placed anywhere on the 3D printer at your willing, with a built-in rechargeable battery, which can be used by pressing the power button. It's especially compact with ANYCUBIC Photon Mono X Printers.. High Density Activated carbon has strong adsorption performance and filtering effect. Anycubic Air Purifier uses a high-density activated carbon filter with a thickness of 18 mm and a weight of 17 grams, which can effectively absorb the odor generated by the resin during the 3D printing process..   , ,   In order to make the activated carbon fully effective, the Anycubic Air Purifier is equipped with a high-quality fan with a high speed of 5,000 rpm, 40 decibels of operating noise, and 30,000 hours of operating life. Faster air circulation, lower noise and more stable operation.. The high-density activated carbon filter element of the Anycubic Air Purifier has a replaceable design. The single activated carbon filter element can work continuously for 3-6 months. After the filter element life expires, the filter element can be easily replaced by simply removing the top cover. Replace the filter element in time, so that you can always breathe fresh air and keep your body healthy during 3D printing..   ,   The Anycubic Air Purifier has a built-in high-quality, rechargeable 18650 lithium battery with a 2,000mAh battery capacity. Anycubic Air Purifier will keep you clean even when you need to continuously print a large model..

9.25'' Larger LCD Screen ANYCUBIC Photon mono X 6k 3d printer is equipped with a 9.25inch monochrome screen, which is 138 larger than a normal 6-inch screen. The monochromatic screen lasts 4X longer than the RGB LCD screen, and a special replaceable scratch-resistant film is added above the screen to save your maintenance costs.. Achieve Larger Print Volume The ANYCUBIC Photon Mono X 6K Resin 3d printer can print up to 9.6 x 7.8 x 4.8 inches HWD. The large volume can print large-size models or multiple models at one time, effectively improving your work efficiency.. High Precision High Resolution The Photon Mono X 6K LCD screen has a high resolution of 5,760 x 3,600 px and a contrast ratio of over 350, which can fully express the details of the character model's hair, fingers and so on. 40 bright LED lights arranged in a matrix provide intense and uniform exposure in each layer of print, improving print quality and accuracy.. Ultra-Fast Printing The max printing speed of ANYCUBIC Photon Mono X 6K 3d printer is 3.15 inh. With a 6 light transmittance screen, the fastest printing speed of the printer can reach 1slayer, saving you half of the time than other regular resin 3d printer and reduces costs.. Compatible Resin Power Adjustment The UV lamp power adjustment range is 30-100, which can support the use of more types of resin printing materials to meet your more printing needs. In addition, adjusting the light power appropriately can extend the lifespan of both the screen and light significantly..

Safer and Ultralow Odor Made from soybean oil, no VOCs, no BPA, no harmful chemicals. Complied with EN 71-32013 safety standard. Easy to Use Stunning Colors High precision and quick curing for LCD 3d printing and high quality pigments provide stunning colors in our range of resins and available colors. Fast Curing Exposure Time Optimized curing time for Anycubic Photon, offering better printing quality. Bottom layer exposure 60-80s Normal exposure 8-10s. Wide Compatibility Sensitive to 355nm405nm UV light. Compatible with most LCD 3D printers. Attention Storage When printing large model, please increase the build plate contact of the model or lower the infill density to avoid wrapping. Store in a dry and dust-free place under 15-35 and keep it sealed and keep it away from sunlight.

Large Model Printing ANYCUBIC Photon Mono X 6K 3d printer has a max print volume of 9.6 x 7.8 x 4.8 inches. The large volume can not only print multiple models at a time, effectively improve work efficiency, but also fully meet the needs of printing large-size models.. 9.25 6K Monochrome Screen The 9.25 resin 3d printer 6K screen has 5760 x 3600 Px, and ultra-high resolution brings vivid details. The life of the monochrome screen is 4X longer than that of the ordinary LCD screen. Added replaceable scratch resistant film, which greatly reduces the damage rate of the LCD screen.. Powerful UV Light Source The Photon Mono X 6K 3d printer with 40 bright LED lamp beads, the newly upgraded 40 LED matrix parallel UV light source, the strong light source distribution is more uniform, so that Anycubic Photon Mono X 6K 3d resin printer can quickly and accurately display the details of each part of the model, showing high quality models.. High Light Transmittance Fast Printing The fast LCD 3D printer using the industry-leading 6 light transmittance screen, the printer's fastest printing speed can reach 1slayer, which saves about half the time compared to ordinary 3d printers and effectively improves printing speed and efficiency.. Adjustable Power The power of the light source can be freely adjusted from 30 to 100, and supports printing of various types of resins. The UV power can be adjusted according to the characteristics of the resin to meet your more printing needs. Moderately reducing the power of the light source can also extend the service life of the exposure screen and light source..

Anycubic Water Washable Resin contains hydrophilic groups with good water solubility, which is can be directly cleaned with water instead of alcohol and greatly save the cost of alcohol use. Besides, it can also be cleaned by Anycubic Wash and Cure Machine or ultrasonic cleaning..    Anycubic UV resin prints the models with low shrinkage during the photo curing process, which ensures the high precision and smooth surface. The low shrinkage rate ensures that every model is printed in good details.. Anycubic water washable photopolymer resin has low odor and it can ensure customers with a better printing experience.. Low resin viscosity means good fluidity in the printing process, which greatly improves the printing success rate. Anycubic upgraded water washable resin has a longer shelf life to 1 and a half years to help the resin to store longer and safe use.. Compatible with 365-405nm wide band, Anycubic resin is suitable for most 3D LCD DLP printers on the market, better effect with ANYCUBIC LCD 3D printers..

Upgrade Protection FunctionSealed washing to prevent the volatilization of alcohol during the cleaning process . Fan-less curing mode makes it quieter to use. The anti-UV lid can block 99.95 of ultraviolet rays to protect your eyes.. Intelligent Curing and WashingThe front TFT screen can directly display the setting time and remaining time, and the operation is simple and intuitive. With built-in 16 pcs of 405nm UV LED and a 360-degree rotating turntable, you can uniformly cure the model.. Flexible Washing ModeThe models can be placed in a cleaning basket to be cleaned separately, or mount the build plate with models on it and wash them together, which can avoid direct touch with the uncured resin. The height of the platform bracket can be adjusted to fit the liquid level in the bucket.. Ideal CompatibilityCompatible with most of the LCDDLPSLA 3D printers like ELEGOO Mars, Mars Pro, Mars C, Photon, Photon s etc, which provides you an ideal support for washing and curing your 3D resin prints.. Special NotesThe washing function is not quite suitable for 3D models printed with water washable resin, which is better to be washed with running water..