Top 10 Best Arduino Motor Controller

Dual-channel H-bridge driver working mode creates higher working efficiency,L298N as main chip, Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors.. To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.. Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability.. High working power to 46v,large current can reach 3A MAX and continue current is 2A, power to 25w.. Large capacity filter capacitance,afterflow protection diode, more stable and reliable..

L298N as main driver chip makes strong driving abilitysmall heatingstrong anti-interferencelow calorific value. Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability. Dual-channel H-bridge driver working mode creates higher working efficiency. To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage. Large capacity filter capacitance, afterflow protection diode, more stable and reliable.

Control speed and direction for two DC motors, or just speed with four DC motors drive a large stepper motor up to NEMA 17.. Connect other sensors and actuators through the shields Molex connectors.. Connect more to your board It works also for up to four external relays or solenoids.. Works with your Arduino Uno, Uno SMD, Mega, and Leonardo.. External power input to separate the motor power from the microcontroller one..

Package 2 pcs.

1. Using dual MOS parallel active output, lower internal resistance, larger current, strong power, 15A, 400W at room temperature, which meets the use of most equipment. Wide voltage, support PWM. Easily realize the control of high-power equipment.

5V isolate with MCU, and effectively protect MCU 5V power indicator on board.. Voltage indication of motor driver output end can solder heat sink.. Just need four lines from MCU to driver module GND. 5V. PWM1. PWM2 isolation chip 5 V power supply can share with MCU 5 V.. Able to reverse the motor forward, two PWM input frequency up to 25kHZ two heat flow passing through an error signal output.. Isolated chip 5V power supply can be shared with the MCU 5V, can also use the on-board 5V supply the supply voltage 5.5V to 27V..

This is a good parts kit for RC car project. It not only comes with 4pcs wheels and motors, but also 2pcs motor drive modules and 60pcs jumper wires, which are very useful accessories for your project.. Motor Drive Controller L298N used as the main driver chip. It has the strong driving ability, low calorific value and strong anti-interference ability.. TT Motor The motor is a two-axis motor with a reduction ratio of 148, which has strong anti-interference ability.. Smart Car Wheels The wheels are made of high-strength plastic and the tires are made of durable black rubber.. To avoid damage the voltage stabilizing chip of Motor Drive Module, please use an external 5V logic supply when using more than 12V driving voltage..

Using L298N made by ST company as the control chip,the module has such characteristics as strong driving ability,low calorific value and strong anti-interference ability.. This module can use built-in 78M05 for electric work via a driving power supply part.But to avoid the damage of the voltage stabilizing chip,please use an external 5V logic supply when using more than 12V driving voltage.. Using large capacity filter capacitor,this module can follow current to protect diodes,and improve the reliability.. Dual-channel H-bridge driver working mode creates higher working efficiency. To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.

Multiple functions, convenient operation, powerful driver library support and function updates.. It can drive 4 DC motors or 2 stepper motors while also driving 2 servos, support the latest for Arduino UNO and for Arduino Mega 2560.. Come with 4 DC motors, 4 Wheels and a set of DuPont cables 20pin male to male20pin female to female20pin male to female. Convenient for enthusiasts to develop quickly based on Arduino.. NOTE IO occupies more. When driving four motors at the same time compared to the Arduino version with less IO, low power..

As the main driver chip, L298N has the characteristics of strong driving ability, low heat generation and strong anti-interference ability, dual H bridge stepper motor driver, the speed and direction of the stepper motor can be controlled.. With SMD aluminum electrolysis uses two 35V 220UF high voltage and high capacity capacitors, 35V 100UF and 10V 100UF low voltage and low capacity capacitors.. Use the built-in 78M05 to work through the drive power supply, but in order to avoid damage to the voltage regulator chip, when using a drive voltage greater than 12V, please use an external 5V logic power supply.. The module uses large-capacity filter capacitors and freewheeling protection diodes to improve reliability..

Contains an I2C-controlled PWM driver with a built-in clock. It means, unlike the TLC5940 family, you do not need to continuously send it signals tying up your microcontroller it's completely free running. 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs, which is good when you want to control white or blue LEDs with a 3.4V forward voltage. Supports using only two pins to control 16 free-running PWM outputs you can even chain up 62 breakouts to control up to 992 PWM outputs.. 3 pin connectors in 4 groups, so you can plug in 16 servos at one time Servo plugs are slightly wider than 0.1 so you can only stack 4 adjacent ones on 0.1-hole female headers.. 12-bit resolution for each output - for servos, that means about 4us resolution at an update rate of 60Hz..