Top 10 Best Clampzilla

Clamping panels can certainly be a challenge. Especially when we try to use everyday pipe clamps or bar clamps. While these types of clamps work fairly well on certain glue up projects, the one thing they dont do at all is apply pressure from the top and bottom of the panels during glue up. In fact, with all the pressure being applied on both sides, bar and pipe clamps will almost certainly bow, buckle or rack your panel glue up project.. Lets make racked panel glue ups a thing of the past The uniquely designed 4 way pressure solves this age old issue by applying pressure to all four sides of your panel glue up. With a simple turn of the rotating clamp handle, all four sides of the clamp will draw inward at the same time. This provides equal pressure on to your panel and prevents bowing, buckling, or racked panels.. Build any length clamp with the durable plastic bars with 4 notches for maximum adjustability to handle a variety of stock widths. Clamp can be used for boards up to 6 inches in thickness by simply adjusting the clamp width capacity with the appropriate number of notches. Turn the handle clockwise to tighten the clamp and turn the handle counter clockwise to release pressure. The 4 way pressure clamp is equipped with side pressure pads to prevent damaging your stock.. Now you can confidently glue up wide boards, shelving, table tops, and more up to 6 thick. To setup the clamps simply attach the clamp to any length 2 x 2s 2 x 4 ripped in half with the the wood screws that are provided, apply wood glue to your project, set the clamps on to your panel boards and turn handle to tighten the clamp on all four sides. We recommend that you place a 4 way pressure clamp every 12 to 18 for best results.. This clamp package comes with two full 4 way pressure clamp assemblies. Includes 2 each rotating handle assemblies, 2 each tailstock assemblies, 4 each side pressure pads and 12 each 4 notch bars. Together, this setup will allow you to create two 4 way pressure clamps. More than one clamp is generally recommended for any project over 12 in length. Wood is required for setting up the clamp. Wood is NOT included..

No more c-clamps when trying to secure a straight edge to your large or small wooden panels Cut large panels, small panels, rout straight dados and more ProGrip Straight Edge Guides are not only great straight edge guides, they are super easy to align and even easier to clamp into place. Made from extruded aluminum and with the extra wide 2-316 inch tube rail, the ProGrip Straight Edge Guide Clamps are robust guides that are made for everyday workshop or contractor use.. Cut straight, true lines with circular saws, routers, trim routers, jig saws and many other power tools you probably own. These clamps are ideal for cutting large sheets of plywood in half with a 50 straight edge guide. Each clamp is identified by the maximum clamping distance between jaws. Another great application for these clamps is cutting dado slots for bookshelves. The alignment and cutting process for dados is so much easier than ever before with the ProGrip Straight Edge Guides.. Each clamp rail is manufactured with a low profile to make guiding your power tool along the edge much easier. The low profile has also been designed with guide accessories in mind. The clamp rails accept many different accessories sold separately or can create your very own jigs and fixtures to use with the ProGrip Straight Edge Guides. Each ProGrip Straight Edge Guide has the exact same profile regardless of length.. How does it work Each ProGrip Straight Edge Guide Clamp has one adjustable jaw and one fixed jaw. The fixed jaw typically will go against the edge of the board closest to you. Once you place the clamp on your board with the fixed jaw over the end, the adjustable end gets drawn in against the opposite side of the board. Once set and aligned, you secure the clamp by simply locking it down with the 3 position lock lever.. The lock lever on each clamp can be secured into one of three positions, each position provides varying amounts of pressure. Depending on your project or application, you may need to apply more pressure by securing the lock lever to the appropriate position. Once secured, the ProGrip Straight Edge Guide Clamp is designed to have zero side to side play with minimal deflection to provide you with the ideal straight edge to make clean, smooth cuts every time.

4-way action of panel clamp applies even pressure to glue joints. Will accept material from 12-inch to 3-12-inches thick of unlimited length. Use while gluing table tops, furniture panels and doors. Package Weight 4.0 pounds.

LARGE PANEL GLUE-UPS The DCT 4-Way Pressure Release Clamp Wood Panel Corner Clamping System Woodworking Bracket Set handles stock up to 6 inches 15.2cm thick for simplifying the process of gluing table tops, countertops, furniture panels, cabinet doors, and more and saves you from using additional clamps to keep the glue-ups straight. 4-WAY Stock stays flat and prevents buckling of boards during glue-up because of the equally applied pressure from all four directions top, bottom, and both sides Ideal for gluing table tops, shelving, veneer, laminates Durable clamp only limited by the quality of prep and glue used. EASY TO USE Assembly instructions included More convenient than lining up standard clamps and cauls Attach notched bars to any length 1.5-inch x 1.75-inch 3.2cm x 4.4cm board equivalent to a 2x4 ripped in half with provided screws, set clamp and turn handle to tighten on large pieces, we recommend one clamp every 18 inches45.7cm for maximum clamping efficiency Make sure the 2x4s you use are not twisted Drill pilot holes for the outer-most screws when attaching the pressure pads. ADJUSTS TO YOUR PROJECT Build any length clamp with the durable plastic bars with 12 notches for maximum adjustability to handle a variety of stock widths Clamp can be used for boards up to 6 inches in thickness by simply adjusting the clamp width capacity with the appropriate number of notches Turn the handle to tighten the clamp and unwind the turn handle to release pressure Clamp has pressure pads to prevent damage to the edge of your stock. CONTENTS Package includes 2 12.75-inch long notch bars, 2 6.9-inch long notch bars, 1 clamp assembly head, 1 clamp assembly tail, 16 assembly screws 4x 38-inch, 12x 1-14-inch L, and assembly instructions 1 set with 1 clamp multiples needed for projects over approximately 2 feet61cm Wood required, not included.

TRACK SAW PRECISION Making straight cuts with a circular saw, router, or jigsaw is a challenging task, but with the BORA 5-PC NGX Clamp Edge System it is quick and easy to break down sheet material and rip boards with clean, accurate cuts every time. 100 OF CUTTING CAPACITY The NGX 50 Clamp Edge is made of heavy-gauge, extruded aluminum that clamps tightly on everything from plywood to dimensional lumber. And for big projects, like a rip cut on a 4x8, increase the length up to 100 inches with the NGX 50 aluminum extension.. STOP THE GUESSWORK Effortlessly attach the NGX Saw Plate to your right- or left-handed saw with the adjustable quick-release clamps. A fixed center molded channel helps reduce blade offset and the aluminum guide rails position your saw to make precision cuts.. REDUCE TEAR OUT Prevent top edge tear-out and splintering with two rolls of 55-inch Self-Adhesive Non-Chip Strip. Attach it to the bottom of the NGX Clamp Edge for a smooth finish. CUT ANY ANGLE Attach the additional two Track Clamps to the Clamp Edge for pro level angle cutting capability.

Clamping panels can certainly be a challenge. Especially when we try to use everyday pipe clamps or bar clamps. While these types of clamps work fairly well on certain glue up projects, the one thing they dont do at all is apply pressure from the top and bottom of the panels during glue up. In fact, with all the pressure being applied on both sides, bar and pipe clamps will almost certainly bow, buckle or rack your panel glue up project.. Lets make racked panel glue ups a thing of the past The uniquely designed 4 way pressure solves this age old issue by applying pressure to all four sides of your panel glue up. With a simple turn of the rotating clamp handle, all four sides of the clamp will draw inward at the same time. This provides equal pressure on to your panel and prevents bowing, buckling, or racked panels.. Build any length clamp with the durable plastic bars with 4 notches for maximum adjustability to handle a variety of stock widths. Clamp can be used for boards up to 6 inches in thickness by simply adjusting the clamp width capacity with the appropriate number of notches. Turn the handle clockwise to tighten the clamp and turn the handle counter clockwise to release pressure. The 4 way pressure clamp is equipped with side pressure pads to prevent damaging your stock.. Now you can confidently glue up wide boards, shelving, table tops, and more up to 6 thick. To setup the clamps simply attach the clamp to any length 2 x 2s 2 x 4 ripped in half with the the wood screws that are provided, apply wood glue to your project, set the clamps on to your panel boards and turn handle to tighten the clamp on all four sides. We recommend that you place a 4 way pressure clamp every 12 to 18 for best results.. This clamp package comes with two full 4 way pressure clamp assemblies. Includes 2 each rotating handle assemblies, 2 each tailstock assemblies, 4 each side pressure pads and 12 each 4 notch bars. Together, this setup will allow you to create two 4 way pressure clamps. More than one clamp is generally recommended for any project over 12 in length. Wood is required for setting up the clamp. Wood is NOT included..

Clamp anywhere with a dovetail groove. Featuring new soft-grip handle.. Unique clamp shape slides into dovetail wood tracks and grooves for fast and easy clamping. Universally compatible with any 12 14-degree dovetail router bit profile. Eliminate the need for expensive T-tracks and groove your own tracks. Work smarter and build taller table saw fences, straight line sleds, and 100s of new clamping jigs. Compatible with 34 x 34 dog holes for quick hold-downs. Note Dovetail Router Bit is not included..

1100 lbs. 500 kg of clamping pressure. 3.5-inch wide padded jaw provides constant, even pressure without damaging material. Passive lock jaw stays in place while winding clamp. Large, easy-grip handle makes it easy to lift and slide jaw up and down. Designed based on end-user feedback.

The clamp can work on a 90 angle and T joint, The V-shaped wedge grips the workpiece firmly, ensure the pieces are fixed at an angle of 90 degrees. Aluminum alloy die-casting clamp body, high hardness, no rust, strong and durable, suitable for the production of the reinforced frame, storage tank, etc. Rubber coated handle design, ergonomic design, anti-skid and wear-resistant The knob adjusts the working pressure to lock firmly at different widths. The quick-adjusting handle allows you to adjust quickly and easily to change the raw materials in the thickness range of 1-1 4 . TIPS Right angle clamp is suitable for 0 to 25 mm thick plate. If the plate is too thick, it will be negative and affect the normal use.

INCLUDES 2 Quick Screw Down Clamps with 7 Max Opening, 2-38 Throat Depth. PREMIUM DESIGN Features high quality and ergonomic plastic clamp handle grips for quick and comfortable tightening, without the splinters from cheap wood The steel pressure pads are completed with removable non marring plastic. SUPERIOR CLAMPING FORCE Delivers consistently secure placement and safe clamp action for a seamless workflow. VERSATILITY These rail clamps provide a portable clamping option for Festool, Makita, Bosh and similar sized track saw guides, perfect as MFT clamps for your homemade workbench, and fits in some heavy duty T-slots see image for size. PLEASE NOTE The clamp ends have a specific profile, see the image for details. They are designed to work with MFT tables, the track saw guides listed and some heavy duty t-tracks with an opening of at least 932. They will not work in universal or t-track. Please check the size of your t-track to verify that the clamps will work for your application..