Top 10 Best Clock Hardware

DIY clock repair kit you will get 5 pieces of high torque long shaft clock movements with 5 different pairs of clock hands, these replacement parts suit well to different styles of clock frame, which are good for repairing, replacing or making a clock by yourself. Size details the total shaft length is approx. 20 mm 0.8 inches, and the thread length is approx. 14.6 mm 0.57 inches Jump second movement is suitable for 9 - 13 mm 0.35 - 0.51 inches thickness of clock panel Please note that small parts are included, keep away from children under 3 years old. Accurate time keeping and quiet motor the long shaft clock mechanism offers great accuracy and dependability Equipped with sweeping motion and no ticking, it will provide you with a quiet environment. Wide application these clock repair replacement parts fit for cross-stitch, three-dimensional embroidery, craft clock, frame-less draw clock, and they are specially suitable to be applied as DIY quartz wall clock replacement movement parts. 5 Different styles of hands this clock kit comes with 5 pairs of clock hands in different styles and length for your options, so it is great for clock creations and repairs while providing a decorative effect.

Size The total shaft length is approx. 20mm 0.79inches, and the thread length is approx. 13mm 0.51inches, fit clock dials 9 - 13mm 0.35 - 0.5inches in thick.. Accurate Time and Quiet Motor The long shaft wall clock mechanism replacement offers great accuracy and dependability, equipped with 6168s silent sweep second movement, no ticking and will provide you with a quiet environment.. 7 Different Styles of Hands This battery clock replacement mechanism set comes with 7 pairs of different pointer and length, great for repairing clocks, clock replacement or making your own customized clock project.. Wide Application These clock repair replacement part kit can be applied in bedroom, living room, office, classroom, restaurant, etc, fit for craft clock, quartz wall clock and so on.. Note When you install this quartz clock movement kit, please keep the hour hand and minute hand parallel, and not tighten the brass hex nut too tight..

Clock movement high torque clock movement with hook, long shaft, drive long clock hands 10 mm to 450 mm. Total shaft length 28 mm 1-1 10 inches, thread length 15.4 mm 3 5 inches, suitable for 9 - 13 mm 9 25 - 1 2 inches thickness clock panel. Size from the center of the hole to the tip the hour hand is approx. 203 mm 8.0 inches long The minute hand is about 305 mm 12 inches in length Note please check the size before buying. Good DIY clock supply suitable for repairing, replacing the broken parts of a clock or serving as good handwork materials to make a clock by yourself. Warm notice there are some clock parts made of aluminum, please do not install them with too much pressure or they will be bent.

Good for repairing, replacing or making a clock.. Young town manufactures the 12888 series in various models,Please check the dimensions of this movement prior to purchase to verify the dimensions.. Applicable to cross-stitch,three-dimensional embroidery,craft clock,frameless draw clock,etc.INSTRUCTIONS - Included along with the movements.. Movement total shaft length 23 mm 2932 inch, thread length 15 mm 1932 inch.. Clock Movement suitable for 9 - 13 mm 2364 - 12 inch thickness clock panel..

Long spindle quartz clock replacement movement parts with metal hook,Good for repairing, replacing or making a clock.. Parameter I Shaft,drive long clock hands 10 mm to 450 mm Total shaft length is 18 mm 4564 inch, thread length is 5 mm 1364 inch,suitable for 1-3 mm 364 - 764 inch thickness clock panel.. DIY clock supplies the complete clock movement kit is suitable for repairing or making a clock, serving as good replacements for large and thick clock frames.. Package contents 1 clock movement with 1 hook,2 Hour hands,2 Minute hands and some mounting hardware, coming with specially designed box and instructions.. Warm notice when you install them, please keep the hour hand and minute hand parallel And please do not use too much pressure to avoid bending them..

DIY clock repair kit you will get 2 pieces of high torque long shaft clock movements with 5 different pairs of hands, these replacement parts suit well to different styles of clock frame, good for repairing, replacing or making a clock by yourself. Size the total shaft length is approx.16 mm 0.63 inches, and the thread length is approx. 9 mm 0.35 inches Jump second movement is suitable for 5 - 9 mm 0.2 - 0.35 inches thickness of clock panel. Accurate time keeping and quiet motor the long shaft clock mechanism offers great accuracy and dependability, equipped with sweeping motion, no ticking and will provide you with a quiet environment. Wide application these clock repair replacement parts fit for cross-stitch, three-dimensional embroidery, craft clock, frame-less draw clock, and specially suitable to be applied as DIY quartz wall clock replacement movement parts. 5 Different styles of hands this set comes with 5 pairs of clock hands in different styles and length for your options, great for clock creations and repairs while also providing a decorative effect.

Clock Mechanism ReplacementGreat for repair, replacement or make a clock, applicable to craft clock, frameless draw clock, 3D large wall clock.. Long Hands SizeHour hand length is about 115 mm4.5 inch Total minute hand length is about 145 mm5.7 inch Second caps is about 165 mm6.5 inch.. Total Shaft Length20 mm0.8 inch, Thread length 14 mm0.6 inch, for 10 mm0.4 inch thickness clock panel.. DIY Repair PartsThe hand is made of aluminum, can be cut according to the size of the dial, replacement part can use to different wall clock styles.. Ultra-silent MovementClock motor sweep silent, no ticking noise, sweep silent with no noise..

Clock mechanism size Total shaft length 78 in, thread length 12 in, fit clock dials from 18 to 38 in thick, repair the old clock, making you smile of the memories your old clock gives you. Decorative long hands With 2 different styles and length for your options, style1 size from the center of the hole to the tip, hour hand is approx 8 in, minute hand 11 18 in, style2 hour hand is approx 5 in, minute hand 6 14 in. Packaged with care Comes as a clock movement with 2 pack long hands kit in a presentation box with custom foam inserts to protect all from scratching, bending, and other damage while shipping. Time-keeping and high torque step movement features High precision and high torque clock mechanism, which ensures watchmaker's accuracy and dependability step motion with a little ticking sound, powered by a AA battery. Keep Time in Style With EMOON clock hands and mechanism combo, you too can be a clock maker perfect for clock replacement, repairing all kinds of clocks, or making your own customized clock project.

DIY clock repair kit you will get 2 pieces of high torque long shaft clock movements with 5 different pairs of hands, these replacement parts suit well to different styles of clock frame, good for repairing, replacing or making a clock by yourself. Size the total shaft length is approx. 28 mm 1.1 inches, and the thread length is approx. 20 mm 0.79 inches Jump second movement is suitable for 13-18 mm 0.51- 0.71 inches thickness of clock panel. Accurate time keeping and quiet motor the long shaft clock mechanism offers great accuracy and dependability, equipped with sweeping motion, no ticking and will provide you with a quiet environment. Wide application these clock repair replacement parts fit for cross-stitch, three-dimensional embroidery, craft clock, frame-less draw clock, and specially suitable to be applied as DIY quartz wall clock replacement movement parts. 5 Different styles of hands this set comes with 5 pairs of clock hands in different styles and length for your options, great for clock creations and repairs while also providing a decorative effect.

Convenient metal hook delicate spindle quartz clock replacement movement parts with metal hook, which is convenient to use. Size detail movement shaft is 28 mm 1-1 10 inches ling, thread length is 20.4 mm 4 5 inches Jump second movement is suitable for 12 - 16 mm 12 25 - 5 8 inches thick clock panel. Center hole to the tip length hour hand is approx. 85 mm 3.3 inch Minute hand is approx. 120 mm 4.7 inch Second hand is approx. 109 mm 4.3 inch. Match power small power consumption, just need 1 of 1.5 V AA battery that can run a long time Warm notice battery is not included in the package. Package detail includes hardware, hanger, 3 hands and protect cardboard box and instructions, make your DIY clock project successful.