Top 10 Best Coping Sled For Router Table

When building cope and stick door and drawer fronts, one of the tasks that must be done is to cut the end grains of your rails. This sounds easy enough, however the narrower your rails are, the more difficult it is to hold the stock firmly up against a router table fence. Our Rail Guide Coping Sled Pro solves this issue and helps you make precise, square, clean cuts for rail and style doors, drawer fronts and most any other type of end grain cut on your router table.. The idea behind the Rail Guide Coping Sled Pro is simple hold your rails firmly at a 90 degree angle to your router table fence so you can feed your stock through the cutter for the cleanest, squarest cuts possible. When doing drawer fronts which often times use very narrow rails, this sled will prevent your stock from dipping or pushing in too far and also keeps your hands away from harm.. We have included a single sacrificial block with the sled to get you started with your first profile. The sacrificial block helps to prevent end grain blowout at the back of your end grain cuts. Also included is an abrasive strip that is adhered to the adjustable fence. The abrasive strip keeps your stock from sliding or wandering during the coping process. That, along with the heavy duty hold down toggle keeps your stock firmly in place.. Many sleds rely on the miter slot for reference. Our coping sled uses the fence as a reference instead. The Rail Guide Coping Sled Pro features a clear acrylic fence for reference which is offset and raised 2 above the base so you wont cut into the sled. Using a fence rather than a miter bar mounted to the bottom means that you will always be parallel to the router table fence. This is a distinct time saving advantage as you will no longer have keep re-adjusting your router table fence. This robust, full featured coping sled has a laminated thick MDF base that slides across your router table surface effortlessly. The sled also features a large, heavy duty hold down toggle with a 1-58 hold down foot to keep your stock in place. The unit also includes two large and sturdy handles for guiding the sled through the cutter. The maximum stock size is 5 wide by 1 thick. Full instructions are included..

PRECISION The size of the shaper coping sled is 375 x 152mm 14.5 x 6 Inch, the rail guide coping sled is the router table accessory you need to make rail style doors, tenons, lap joints. This full featured coping sled has a aluminum base that slides across your router table surface effortlessly. The unit also includes two large and sturdy handles for guiding the sled through the cutter.. USAGE When building cope and stick door and drawer fronts, one of the tasks that must be done is to cut the end grains of your rails, the rail guide coping sled solves this problem, helps you make precise, square, clean cuts for rail and style doors, drawer fronts and most type of end grain cut on your router table.. PRACTICAL Fix your rail firmly at a 90 degree angle with your router table fence, you can cut your stock into the cleanest and most square shape through the cutter. When narrow rails are often used on the front of the drawer, this sled can prevent your inventory from being immersed or pushed too far, and can also keep your hands away from injury.. STABLE Add a separate sacrifice block in the sled to allowing you to start using your first profile. Sacrificial block is easily replaceable to accommodate different profiles. The abrasive belt can prevent your stock from sliding or drifting in response. This, coupled with the heavy press switch, can keep your stock firmly in place.. REFERENCE Transparent guide runs along the fence 51mm 2 above the table, to enable compatibility with most router table fences and prevent cutting into the sled. Using a fence instead of a miter bar installed at the bottom means that you will always be parallel to the router table fence. This is a significant time saving advantage, as you will no longer need to constantly readjust the router table fence..

EXCELLENT FEATURES When building cope and stick door and drawer fronts, one of the tasks that must be done is to cut the end grains of your rails. This sounds easy enough, however the narrower your rails are, the more difficult it is to hold the stock firmly up against a router table fence. Our Rail Guide Coping Sled solves this issue and helps you make precise, square, clean cuts for rail and style doors, drawer fronts and most any other type of end grain cut on your router table.. EASY TO USE The idea behind the Rail Guide Coping Sled is simple hold your rails firmly at a 90 degree angle to your router table fence so you can feed your stock through the cutter for the cleanest, squarest cuts possible. When doing drawer fronts which often times use very narrow rails, this sled will prevent your stock from dipping or pushing in too far and also keeps your hands away from harm.. PERFECT WOODWORKING TOOL SET The sled set included a single sacrificial block with the sled to get you started with your first profile. The sacrificial block helps to prevent end grain blowout at the back of your end grain cuts. Also included is an abrasive strip that is adhered to the adjustable fence. The abrasive strip keeps your stock from sliding or wandering during the coping process. That, along with the heavy duty hold down toggle keeps your stock firmly in place.. SAVE TIME Our coping sled uses the fence as a reference. The Rail Guide Coping Sled Pro features a clear acrylic fence for reference which is offset and raised 2 above the base so you won't cut into the sled. Using a fence rather than a miter bar mounted to the bottom means that you will always be parallel to the router table fence. This is a distinct time saving advantage as you will no longer have keep re-adjusting your router table fence.. PRACTICAL WOODWORKING TOOL The Rail Guide Coping Sled is an indispensable tool for making precise, square, clean cuts for door and drawer fronts..

Our 525 Large Coping Sled works on both the router and shaper, either in the miter slot or against the fence. This is the safest and most accurate way to make cope cuts and other cross-cuts on a router table or shaper. Don't try to cope without it Two adjustable feed handles provide firm control over the sled and your work.. Includes an 11-34 long 34 wide adjustable steel miter bar that mounts in 6 different locations for best placement. Can also be used without the miter bar against your fence.. Holds stock up to 10 wide. Heavy duty 12 phenolic base 15-34 x 15-34 will not distort from clamp pressure.. Features one 500 lb. Outboard Toggle Clamp and two 500 lb. Inboard Toggle Clamps. Hold stock up to 1-34 thick, or 2-34 with optional 6305R Riser Kit one Riser Kit required for each toggle clamp. Fence is 24 long. Optional 525S Flip Stop available for repetitive work.. Lifetime guarantee against defects in material or workmanship. Made in the USA.

Sacrificial block is easily replaceable to accommodate different profiles. Maximum workpiece dimension is 5'''' wide x 1-14'''' thick. Solid brass indexing keys ensure uniform spacing and tight finger joints. Sacrificial MDF fence face helps control tearout.

Our 526 Medium Coping Sled works on both the router and shaper, either in the miter slot or against the fence. This is the safest and most accurate way to make cope cuts and other cross-cuts on a router table or shaper. Don't try to cope without it Two adjustable feed handles provide firm control over the sled and your work.. Includes an 11-34 long 34 wide adjustable steel miter bar that mounts in 6 different locatons for best placement. Can also be used without the miter bar against your fence.. Holds stock up to 6 wide. Heavy duty 12 phenolic base 11-58 x 11-34 will not distort from clamp pressure.. Features two 500 lb. Inboard Toggle Clamps. Hold stock up to 1-34 thick, or 2-34 with optional 6305R Riser Kit one Riser Kit required for each toggle clamp. Fence is 12 long. Optional 525S Flip Stop available for repetitive work.. Lifetime guarantee against defects in material or workmanship. Made in the USA.

Our 528 Small Coping Sled works on both the router and shaper, either in the miter slot or against the fence. This is the safest and most accurate way to make cope cuts and other cross-cuts on a router table or shaper. Don't try to cope without it Two adjustable feed handles provide firm control over the sled and your work.. Includes an 11-34 long 34 wide adjustable steel miter bar that mounts in 6 different locations for best placement. Can also be used without the miter bar against your fence.. Holds stock up to 6 wide. Heavy duty 12 phenolic base 7-58 x 11-58 will not distort from clamp pressure.. Features one 500 lb. Inboard Toggle Clamp. Hold stock up to 1-34 thick, or 2-34 with optional 6305R Riser Kit one Riser Kit required for each toggle clamp. Fence is 12 long. Optional 525S Flip Stop available for repetitive work.. Lifetime guarantee against defects in material or workmanship. Made in the USA.

Coping Sled For Router Table If you're building cope-and-stick doors and drawer fronts, our new rail coping wood sled will be an indispensable helpmate. The Rockler rail coping jig has taller round handles that allow a firm, comfortable grip from any angle of approach.. Smooth-Running Sled With its smooth-sliding phenolic base, and sturdy toggle clamp holding your stock firmly against the router fence, your rails will travel unwaveringly past the cutter for the cleanest, squarest cuts you can imagine.. Keeps Your Hands Safe Particularly with drawer fronts, which sometimes use very narrow rails, the rail guide coping sled prevents parts from dipping in too deep and keeps your hands safely out of harm's way.. Prevent End grain Blowout A sacrificial block can be attached to the fence to prevent end grain blowout, while an abrasive strip prevents the workpiece from wandering.. Whats Included Our router table woodworking kit includes a Sled Base, Fixed Fence, Adjustable Fence, Lever Clamp, Sacrificial Piece, Front Handle, Rear Handle, 2 1'' Round Knob, 4-Star Knob, 2 Large Washers, 4 Small Washers, 2 Spacers, 516''-18 TPI x 1'' T-Slot Bolt, 516''-18 TPI x 1-1 2'' T-Slot Bolt, 3 516''-18 TPI x 2-1 2'' T-Slot Bolt, 4 Cap Nut, 4 1-3 4'' Mounting Screws, 2 8 x 1-3 4'' Wood Screws, Abrasive Strip, Manual.

MAKE YOUR OWN SLAB TABLES With the Woodpeckers Basic Slab Flattening Mill you can now use your router to flatten slabs right in your own shop faster and easier that you ever thought possible.. NICE CAPACITY The Basic Slab Flattening Mill capacity is 38 x 57.. INCLUDES Includes 2 72 rails, 2 48 rails, 1 router sled, 4 Slab Clamping Dogs and all assembly hardware. Does not include plywood or MDF base.. BUILT IN USA This Woodpeckers product is proudly built in the USA..

The setup blocks can easily set the height of the fence, blades bits and other cutters according to the needs, which is faster and more accurate than using a combined ruler.. Combine bars to setup 100's of measurements. Stack setup bars for a wide variation or sizes, or use on their own, work and measure quickly.. Set up gauge blocks are all 4 inches extra long. Accurate gauge block set sizes 116, 332, 18, 316, 14, 12, 34, 1x87x4. Easy-to-read laser etched labels on each block. Fitted case included, so the combination square will be more tightly protected during transportation.. 8 pcs Blocks Solid Aluminum Construction Black Anodized to better protect router bits and saws..