Top 10 Best Dc Motor Driver

DROK DC motor driver input voltage range is DC 6.5V-27V, can be input DC 12V or 24V, rated output current of each port is 7A, total output power is 160W.. STRONG DRIVE the motor controller board adopts dual H bridge, can drive two DC motors at the same time.. FORWARD and REVSERSELY ROTATE the IN1, IN2IN3, IN4 port can control forward or reverse motor rotation.. PWM SPEED CONTROL enable signal terminal ENA input PWM can regulate speed, PWM frequency range 0-10KHZ.. UNDER VOLTAGE PROTECTION the motor driver module is with under voltage protection to prevent instantaneous large current from damaging the module..

L298N as main driver chip makes strong driving abilitysmall heatingstrong anti-interferencelow calorific value. Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability. Dual-channel H-bridge driver working mode creates higher working efficiency. To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage. Large capacity filter capacitance, afterflow protection diode, more stable and reliable.

Package 2 pcs.

Operating Voltage DC DC 5V--36V continuous current 15A at normal temperature power 400W The maximum current can reach 30A under auxiliary cooling conditions.. Trigger signal source digital high and low level DC3.3V--20V, can be connected to single-chip IO port, PLC interface, DC power supply, etc., can be connected to PWM signal, signal frequency 0--20KHZ support. Adopt imported dual MOS parallel active output, lower internal resistance, large current, strong power, 15A, 400W at room temperature, meeting the needs of most equipment. Application The output can control high-power equipment, motor, bulb, LED strip, DC motor, micro pump, solenoid valve, etc. It can input PWM, control motor speed, lamp brightness, etc. Wide voltage, support PWMEasily control high-power devicesService life unlimited switch working temperature -40-85 C size 1.34x0.7x0.5inch3.4 x 1.7 x1.2cmLWH.

Use of imported original chip, built-in low on-resistance MOS switch. Dual H-bridge motor driver, can drive two DC motors or a 4-wire two-phase stepper motor. Dual 1.5A 2, the peak current to be 2.5A, built-in thermal protection circuit, do not be afraid motor stall burned, automatic recovery after the temperature dropped. Minimal heat, no heat sink, small size, low power consumption, is ideal for battery powered. Small size, light weight, low standby current, is the ideal choice for your car model.

Using L298N made by ST company as the control chip,the module has such characteristics as strong driving ability,low calorific value and strong anti-interference ability.. This module can use built-in 78M05 for electric work via a driving power supply part.But to avoid the damage of the voltage stabilizing chip,please use an external 5V logic supply when using more than 12V driving voltage.. Using large capacity filter capacitor,this module can follow current to protect diodes,and improve the reliability.. Dual-channel H-bridge driver working mode creates higher working efficiency. To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.

The Motor Shield is based on the L298 , which is a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors.. It lets you drive two DC motors with your board, controlling the speed and direction of each one independently. You can also measure the motor current absorption of each motor, among other features.. Motor controller L298P, Drives 2 DC motors or 1 stepper motor. Package 1pcs Motor Driver Module. If You Are Not Satisfied with Your Purchase for Any Reason, Please Feel Free To Contact Us at the Buyer Center or Support Email, 247 Quick Reply..

Suitable for Nema 23 ,Nema 24 and Nema34 Stepper Motor2-phase hybrid stepper motors Outer diameter 57, 60,86mm.. This high subdivision driver is suitable for high subdivision motor. Suitable for stepper motor 57,60,86 type 2-phase 4-wire, 6-wire, 8-wire. Anti-Resonance for optimal torque, extra smooth motion, low motor heating and noise. Package 1piece DM556 driver. PLEASE NOTE if there is any problem, please feel free to contact us, each defect items could be refunded or reshipped, we will try out utmost to support you..

HiLetgo L9110S H-bridge DC Stepper Motor Driver Controller Board. Dual motor driver chip L9110S. Module supply voltage 2.5-12V.