Top 10 Best Ender 3 Pro Parts

This Ender 3 touch screen is now FULLY open source thanks to a partnership between First Layer with Insanity Automation. The ONLY open source Ender touch screen on Amazon fully Plug-And-Play from the factory flashed with our custom firmware for more features than ever. NEWLY SUPPORTED dual gear extruder, filament sensor, mesh bed leveling features, change filament function, screen brightness and standby timer, built in PID tuning, silent touch screen mode, direct drive extruders and more. A custom DWIN_SET makes this the first open source Ender series touch screen on the market to be compatible with any Ender 3 V2 Pro 5 5 Pro on the market. Along with more added features than any other touch screen available today, this is THE best version of this product available on Amazon right now. With this new open source build, not only have critical bugs preventing users from even turning on their printers been fixed, but more printers than ever can use this touch screen. This is the newest version of Creality's 4.2.7 32 Bit silent control board with authentic TMC2225 Trinamic stepper drivers which greatly reduce the sound of the stepper motors during use. The 4.2.7 control board comes flashed with our custom Marlin firmware for the Ender 3 Pro. This entire hardware swap will take less than 1 hour and quickly turns your stock Ender into a touch operated printer in just one upgrade as well as add dozens of features over stock Creality firmware. The upgraded silent fan included can be placed on the hotend or the control board however since the hotend fan is running at all times, it is suggested to be installed there. To avoid needing to re-route all the wires through the wire harness, you can cut the wires from the old fan and splice them onto the new silent fan for a pain free swap. First Layer have partnered with Insanity Automation to hack this touch screen and unlock its full open source potential This kit is completely Plug-and-Play and enhance your Ender 3 with previously unavailable features, while also allowing for the BL Touch upgrade in the future if you want to install it. Please note this Touch screen is flashed with a custom DWIN_SET folder developed by Insanity Automation for First Layer. Stock Creality firmware for the 427 board WILL NOT work with this screen.

11 Meter Original Capricorn XS Serious Bowden PTFE tubing with lowest friction on the market. Less friction means more responsiveness, less retraction, more accurate prints, less slippage, wear, and tear on the extruder, and less clogging when printing chunky filaments such as some woodfills or ironfills.. 1 PTFE cutter with an extra sharp razor is also included to ensure that the PTFE is cut flat on both sides to prevent any malfunctions or heat creep when feeding and retracting.. 2 PC4-M6 and PC4-M10 Pneumatic Fitting to secure PTFE in extruder and hotend.. 2 MK8 hotend socks are also provided to help keep temperatures on the hotend much more stable and this will result in higher print quality and more consistency.. 20.4mm nozzles of non-stick silicone material Help to keep the hotend temperature extremely stable..

It's 100 Creality Original Upgrade Assembled Extruder Hotend.. Original Capricorn XS Serious Bowden PTFE tubing with lowest friction on the market. Less friction means more responsiveness, less retraction, more accurate prints, less slippage, wear, and tear on the extruder, and less clogging when printing chunky filaments such as some woodfills or ironfills.. Pluggable the heating tube and temperature thermistor that from control box, connect them with terminal housing and pin. Then you could plug the hotend kit, easier to replace hotend kit.. With more terminal housing and pins as spare parts, in case fail installation and waste.. MK8 Extruder Hot End kit, white wire was temperature thermistor, braided wire was heating tube 24V40W..

High Quality 100 New, durable and good performance, fully assembled, you can install directly and easily.. Compatibility 3D Printer full assembled MK8 extruder set For Ender-3 Ender-3s Ender-3 Pro and more 3D printer.. High Temperature Resistance Stainless steel material nozzle throat and high quality resistance whose temperature can up to 260 C 500 F. Package List Mainly including 2 fans, fan covers, heat block, cooling block, nozzle, throat pipe, connector, teflon pipe, thermistor sensor, heating tube, screws, gaskets, etc.. Surprise GiftComes with 4 nozzles and a black silicone sleeve for free in the package..

pSimple Assemble No welding, No modification, No need other tools, Easy to install.p. pHigh Quality with All-aluminum coupling and 42-34 stepper motor, Double Z structure runs smoothly.p. pMature Solution The dual z axis upgrade kit is compatible with Ender 3 Ender 3 Pro Ender 3 V2 3D printer.Easily improve 3D printers with low cost efficiency to Dual Z axis mode.. pCost Effective Minimal cost upgrade and maximum optimizationp. pG-Hubble Promise Tested before leaving the factory, product , .p.

Quality Assurance100 official all-metal 3D printer extruder. High quality aluminum alloy material and sandblast to surface oxidization, ensuring this gray extruder is last for long term use. Works better than original plastic stock extruder. Original Creality 3D printers accessories for Ender-3Ender-3 ProEnder-3SEnder-3 V2Ender-3 MaxCR-10CR-10S.. Work BetterOur 3d printer extruder kits have an adjustable bolt so that you can adjust the pressure of the extruder gear as needed. The extruder drive has better stronger pressure pushing the filament into the printer nozzle and so will improve the printer's performance. 40 Teeth drive gear feeds the 1.75mm filament, compatible with PLAABSWoodTPUPTEG.. Improved PerformanceThe optimized extruder with metal extrusion and original hotend kit pushes the filament into the printer nozzle, greatly making the metal extruder retain power in filament feed-in. And the beveled filament intake can prevent scraping the filament as it is pulled into the feeder.. Easy To InstallDIY kit and you need to assemble by yourself. The full necessary screws parts kit for the extruder is included. Referring to instructions or our 5th picture to install, it is very easy and straightforward to switch to this upgraded part on your machine.. After Sales SupportMore than 20 engineers provide 247 customer service with 12-months limited and lifetime technical assistance. Please kindly contact usseller via ask a question find us directly cause our customer service will respond to you within 24 hours no matter what question..

Material POM. Outer Diameter 24mm, Inner diameter 5mm, Height 11mm. Application Used for 3D Printers. If you have any problem or question,please feel free to contact us.

Original Aluminum Drive Feed for Creality 3D CR-7, CR-8, CR-10, CR-10 S4, CR-10 S5, it is stable and durable.. MK8 extruder drive feed kit, can replace acrylic parts of CR-10, CR-10 S4, CR-10 S5.. Full Metal Aluminum Alloy. Used for 1.75mm filament. DIY aluminum block, need to assembly by yourself.

Apply for 3D printer like CR-10 Series Z-axis or Ender-3 XYZ-axis, machinery and equipment.. 1.8 degree step angle, 0.4N.M holding torque, with 0.8A rated current per phase.. Motor size 42 42 34mm 1.7 1.7 1.3in. NoteOnly step motor is included. The connecting cable is not included.. After the product is purchased, if you have any questions, you can contact the seller at any time, and we will solve it for you within 24 hours..

ATTENTION BEFORE USEFirstly, please make sure the bottom of the soft magnetic sticker and the top layer are firmly adsorbed before installation. If it cannot be adsorbed, please rotate it 90 degrees and try again until they are completely adsorbed and will not separate. Secondly, after finding the correct magnetic direction, then you can stick the bottom part on the hot bed. Please pay attention to the direction before installation.. ALL NEW FUNCTIONALITY Introducing the first ever removable, magnetically secured, build surface for hassle free model removal.It is recommended to heat the hot bed for 2-3 minutes before removing the model with the removal tools.. EASY MODEL REMOVAL The first 3D printing surface designed with model removal in mind. This surface is easily removed, and flexible. Simply print on the surface, remove the upper magnetic surface from the lower, bend the flexible surface and watch the model fall right into your hands.. CUSTOMIZABLE The flexible surface can easily be cut to any demensions making it perfect for all build sizes and all FDM printer models.. SIMPLE INSTALLATION UNIVERSAL Build surface comes with upper magnetic build surface and lower magnetic adhesive base. Place lower 3M adhesive surface on top of normal build plate.Works with all FDM printer models, and all heated and non-heated 3D printer beds..