Top 10 Best Filament Runout Sensor

Auto Filament Runout SensorBIGTREETECH smart filament sensor can not only detect filament runout but also filament break and filament jam. After detecting above abnormal extrusion circumstances, our smart filament detector will conduct auto pause or stop print depend on your set-up in advance to help save print and remove you from filament waste.. High Compatibility for Multiple DisplaysBreak detection sensor can support 2004LCD,12864 LCD. W hats more,it also supports both working modes of marlin and touch screen mode for TFT24TFT35 E3 V3.0TFT70 V3.0 and other touch screen of BIGTREETECH.. Two Extrusion Can be RealizeSupport remote and direct two extrusion ways and 1.75mm diameter filament.. What Control Boards Can be Compatible with The board which has break detection interface can be used,like SKR V1.3SKR V1.4 TurboSKR MINI E3GEN L control board.. Firmware Modification Smart filament sensor use Marlin2.0.x firmware,you follow our github guide to modify firmware of your 3D printer. If you have any problem in setting up, please feel free to contact us for help..

High Compatible Suitable for Ender 3 Ender 3 V2 Ender 3 pro Ender 3 MAXEnder 5 Plus CR-10S PRO CR-10 V2 V3 with 32 bit V4.2.2V4.4.7. Only Ender 3 Series need to replace extruder bracket.. Smooth filament travelling The filament sensor has a built-in filament guider, which is made of metal material with smooth surface, reducing friction resistance and ensuring smooth filament feed-in.. Precise Detection Blue LED indicates normal filament feed-in, when the Blue LED turns off, it means filament runs out.. Upgraded DesignIt is redesigned with new inner structure. The outer cover is frosted, making it stylish and unique.. After Sales ServiceCreality pays great attention to the buyers user experience. If you have unsolvable problems during installation and use, please feel free to contact us, our after-sales technical team will provide you with detailed solutions within 24 hours..

3D Printer AccessoriesVery practical filament detection sensor module, ideal accessories for 3D printer, making your printing work smooth and relieved.. Main FunctionFor checking the filament is whether run out or not, it automatically stops the 3D Printer when the filament runs out.. Filament Detection ModuleNewly designed smart module, The main board executes the pause command operation when the filament is run out.. Extended Product LifeA wear-resistant copper sleeve is added to the feed port and the discharge port at the same time can effectively prolong the service life of the product.. After-sales Guarantee Each defective item can be replacement for free or refund. If any question, please feel free to contact or QA us, we will try our best to service you..

Only used for 32bits motherboard like version 4.2.2, 4.2.7. Suitable for Ender 3 Ender 3 V2 Ender 3 pro Ender 6 CR-10S PRO CR-10 V2 V3ENDER 3 MAX. But the installation bracket is only used for Ender 3 series, as Ender 6 and cr10s pro printer already have the sensor installation holes or bracket. Independent Modularized Design it is redesigned with new inner structure. The outer cover is frosted, making it stylish and unique Filament breakage detection device contains micro switch, using the principle of mechanical proximity switch, no friction, can ensure the smooth feeding of filaments.. Precise Detection Blue LED indicates normal filament feed-in Blue LED turns off when filament runs out.. IMPORTANT For Ender 3 V2, Ender 3 and Ender 3 pro, you need to flash your motherboard's firmware before using, about the firmware download way, please check the following description or the instrument in the pack. as Ender 6 and CR10S PRO printer's firmware has been setted with filament detection function, so you can use them directly.. Package 1 filament detector sensor, 1 extended cable, 1 installation bracketThis bracket is only used for Ender 3 V2 Pro, Filament detection bracket or holes already set up in the Ender 6 and CR10S PRO.

This filament runout sensor is designed for detect whether your filament is run out during the printing process.. The sensor will send the signal to the printer when the filament is run out and printer will pause the print job until the new filament is loaded when the printer w correct firmware and setting.. 1pc Runout Sensor, 1pc 3pin Cable, 3pc Cable Connectors, 2pcs Screws w nuts, 1pc PTFE Tube.

Use on lerdge board the green light for the module is always on when material is available. When the material is used up, the green light goes out. The main board executes the pause command operation and waits for the personnel to replace the good material and then continues to print.. Lerdge main board wiring M sensor port on the main board.. For other boards material detection module uses level jump detection method.. When there is material, the level signal of the detection port should be high. When there is no material, the level signal of the material port becomes low, and the system detects one. If the high to low conversion is determined, the material is considered exhausted and the pause command is executed. After humans change the material, the printer continues to print.. Suitable for 3D printer run-out, pause detection..

This 1.75mm filament run out sensor unit is design for detect whether your printing is run out of filament. During printing if the unit detected that there is out of filament it will send a signal to the main board. With correct firmware settings the printing will paused untill the operator reload the filament and resume the printing.. This Filament breakage sensor save your filaments when a strike occures. Its cover is made from Aluminum material, red surface treatment, looks beautiful.. Filament breakage detection device contains micro switch, using the principle of mechanical proximity switch, no friction, can ensure the smooth feeding of filaments.. Precise Detection Blue LED indicates normal filament feed-in Blue LED turns off when filament runs out.. Original from Creality, can be used without any adjustment for Creality CR-10 V3 SV03 CR-10 V2 CR-10S Pro CR-10S Pro V2 CR-10 Max CR-10 Max Ender-3 Max Ender-6 CR-3040 Pro CR-5Pro 3D Printer.

Smart module for detecting the status of the filament.. Suitable for Ender 3 Ender 3 V2 Ender 3 pro Ender 3 MAXEnder 5 Plus CR-10S PRO CR-10 V2 V3 with 32 bit V4.2.2V4.4.7. Only Ender 3 Series need to replace extruder bracket. Independent modularized design It has been redesigned with new internal structure. The outer cover is frosted, the manufacturing is stylish and unique.. Precise detection the blue LED indicates normal filament feed and the blue LED goes out when the filament runs out.. Smooth Filament Travel The Ender 3 V2 filament breakage detection device contains a microswitch, which uses the principle of mechanical proximity switch, no friction, can ensure the smooth feeding of filaments..

Independent Modularized Design, Compatible with CR-6 SE, CR-6 MAX, Ender 3 S1, Ender 3 S1 Pro, CR-10 Smart, CR30, Sermoon D1 and 3DPrintMill 3D Printer, but not stuiable for Ender 3, Ender 3 Pro V2, CR10, CR10 S4 and S5, please know before ordering.. Smooth filament travelling The filament sensor has a built-in filament guider, which is made of metal material with smooth surface, reducing friction resistance and ensuring smooth filament feed-in.. Precise Detection Blue LED indicates normal filament feed-in. Blue LED turns off when filament runs out.. It is redesigned with new inner structure. The outer cover is frosted, making it stylish and unique.. Size 40x31x18mm, used for 1.75mm diameter filament..