Top 10 Best Hot Surface Igniter For Gas Furnace

Model Number CECOMINOD002711. Item Package Length 6.099999993778. Item Package Width 3.099999996838. Item Package Height 3.099999996838.

HOT FURNACE OVEN IGNITER-- hot surface ignitor lh33zs004 is applied safe and premium materials, to light the hot gas surface and adjust the temperature normally. And it has been tested in several processes before leaving the factory, guarantee its quality meet OEM standard. REPLACEMENT MODEL--Our hot surface ignitor for gas furnace compatible with Carrier, Bryant, Payne, and Day Night gas furnaces. Directly replace LH33ZS004 LH33ZS003 LH33ZS002 LH33ZS001. Any uncertainty about the compatibility, contact us and we will check for you. NO WORRIES ABOUT-- successfully release your worries about the hot surface not heating or heating abnormally, the furnace running erratically and furnace was burned out etc. Use hot surface ignitor lh33zs004 with higher quality could protect your oven and extend its lifespan. QUICK INSTALL-- Remove the old hot surface igniter and reconnect the wires with yours, just cost few minutes. Please be careful and unplug stove before making repairs. PROTECTIVE PACK-- The Heating Rod on furnace ignitor lh33zs004 is pretty fragile, so we pack it with foam to reduce the number of damage. If you receive damaged furnace igniter, please contact us timely so we could provide you replacement or refund services.

Duralight Two Year Replacement Warranty. Made In USA. Exact Fit with No Adapters or Wiring Changes Required. Direct Replacement Part For Most Rheem, Ruud, Weatherking Furnaces With Hot Surface Ignitors - Will Not Fit Drum Heat Exchanger Type Furnaces. Replaces Part Numbers 62-22441-01, 62-22548-01, 62-22868-01, 62-22868-02, 62-22868-82, 62-22868-92, 62-22868-93S, 62-22869-01, 62-23460-01, and 8553-5514.

Duralight Two Year Warranty. Made In USA. Correct OEM Plug Requires No Modifications. 5-14 Long Insulated Wires - Includes Two High Temperature Ceramic Wire Nuts. Replaces Unitary Products Group York, Luxaire, Coleman, Coleman-Evcon, FraserJohnson, and Air Pro Part Numbers S1-02535325000, 025-32626-000, 025-31801-000, 025-30277-700, 025-31802-000, 025-30385-700 and 025-32625-000.

120 volt nitride furnace igniter Replaces hot surface ignitor for gas-fired furnace, boiler, and water heater. How to tell if your igniter is working if the igniter has continuity your multimeter should read anywhere from 9 to17 Ohms,if there is no reading on the multimeter or very little change, then there is no continuity and you will have to replace the nitride furnace igniter. 1.97 Nitride heating element, 1.18Ceramic insulator body nonglazed 95 alumina- polished finish, 15-34 inch temperature rating 250 cable- 20 AWG UL 10362 specification. It works compatible with Cook Top, Cook Top and Range, Furnace and Warm Air Movement, Gas Ignition, Hot Surface Igniters, Infrared light source, Pool Heater and Boilers, Process Machinery, Special FX, Water, and Parking Heaters Nitride heating element. Power rating150 W. Temperature at 120v 0.5v .60HZ at 17 sec 1180 .This is a very versatile product, very robust with long cycle life. Silicon nitride is extremely rugged and can be handled without fear of breakage or contamination..

PERFECT FIT- 62-22868-93 hot surface ignitor is perfectly compatible with Rheem, Ruud, and Weatherking furnaces NOTE Not To Fit -gec or -ged drum Heat Exchanger Type Furnaces. REPLACEMENT MODEL- 62-22868-93 furnace ignitor replaces part number 62-22441-01, 62-22548-01, 62-22868-01, 62-22868-02, 62-22868-82, 62-22868-92, 62-22868-93S, 62-22869-01, 62-23460-01, 8553-5514 Contact us if you are not clear the compatibility, and we are here to help within 24 hours. EXCELLENT PERFORMANCE- The 62-22868-93 furnace hot surface ignitor with wire connectors is used to light the oven burner and adjust the temperature normally. It fixes the symptom that the oven failing to heat or not heat properly. Use this high-quality replacement part to extend the life of the oven. PREMIUM QUALITY EASY INSTALLATION- Our 62-22868-93 furnace ignitor for rheem is made of durable and high-quality materials well-tested by the manufacturer, with higher heat resistence, durability and the best quality for greater power connection, higher load and longer service life. It is fairly easy to install. If wire connector does not match up you will need to cut off the connector and splice the wires with porcelain wire nuts. SHOP WITH CONFIDENCE- Funmit adhere to provide all customers with a simple, streamlined shopping experience of large appliance replacement parts, and prove that we have the highest quality parts and service out there. We stand by our products, and our customers are our focus as a business. If you have any quality problem, please contact Funmit customer service team in time, and we will try our best to solve your problems.

Made from high-purity recrystallized silicon carbide crystar which combines physical and thermal strength with stable electrical properties. Designed to reach ignition temperatures within 17 seconds. Have 18-gauge nickel chrome lead wires embedded and metalized in place for maximum holding strength and electrical conductivity. Manufactured with lead wires enclosed in a special high-temperature fiberglass insulation providing electrical protection. Operate at 120 vac. Some modules are rated for 208240V input, however, the voltage to the ignitor is stepped down to 120 vac.. Hot Surface Igniter. HOT SURFACE IGNITOR WPLUG. Replacement Part.

Duralight Two Year Warranty. Made in USA. 90 Degree Mounting Bracket and Two High Temp Wire Nuts Included. Will Also Work With Existing Snap-In Bracket. Replaces Goodman - Amana - Janitrol Part Numbers B1401015 and B1401018.