Top 10 Best Load Cell

Tension and compression both can be used. High accuracy with good stability. Hermetically weldedsealed by adhesive inside. Oil-proof, waterproof. material alloy steel.

Load Cell Easy to use. With 5-10V driving voltage, the force change is directly output as a voltage signal.. HX711 module A 24-bit AD converter chip specially designed for high-precision load cells.. Connection Red to E Black to E- Green to A White to A-.. Two-way optional differential input On-chip low-noise programmable amplifier with selectable gains of 64 and 128.. Instructions One end of the sensor is fixed by a screw hole, and the other end is left in the air. Apply force in the direction indicated by the label. Please be careful not to directly press the white latex part to avoid damage to the sensor..

HX711 module uses 24 high precision AD converter chip hx711 HX711 a specially designed for the high precision electronic scale design with two analog input channel the internal integration of 128 times the programmable gain amplifier.. LOAD CELL - Sturdy aluminum alloy construction with strain gauges pre-attached with strain relieved wires. Accurately measures forces from 0-5kg 0-11 lb.. On-chip active low noise PGA with selectable gain of 32, 64 and 128.. On-chip power supply regulator for load-cell and ADC analog power supply, on-chip oscillator requiring no external component with optional external crystal.. Simple digital control and serial interface pin-driven controls, no programming needed, selectable 10SPS or 80SPS output data rate..

The 50kg load cell is a group of half-bridge strain gauge, there are 3 ways to use it. 2.Use two sensors to form a full-bridge measurement, measuring range for the sum of the two sensors 50kgx2 100kg. Use one load sensor 50kg with an external resistor to form a full-bridge measurement, the range of a sensor range 50kg. External resistance on the higher requirements.. Use two weight sensor 50kg to form a full-bridge measurement, measuring range for the sum of the two sensors 50kgx2 100kg. Use four weight scale 50kg to form a full-bridge measurement, measuring range for the sum of four sensors 50kgx4 200kg. If you have any problem, please contact seller as follow click DIYmallsyou can find Sold by DIYmalls under Buy Now button, in the new page, click Ask a question..

Made in Thailand. Power adaptercharger input 100-240 volts AC. NiMH rechargeable battery pack inside.. Accuracy better than 0.5 of FS Full Capactiy for Capacity 5N-1000N model. And 0.5 of FS Full Capacity for 3,000N-20,000N model. Tension or Compression Load. Peak Hold or Track Mode., 500 reading can be recorded on internal memory, for later viewing or download. Two M12 thread ball bearing holder provided, to attached to Load Cell.. Metal Enclosures. 2 Bearing Holder provided. Power by internal rechargeable NiMH battery pack or directly from wall plug charger.. Complete set with carrying case, charger. For Capacity 3,000N-20,000N load cell with bearing holder are provided. on both end. Calibration Certificate included. Ideal for tension testing but can also be applied for compression testing.

The Load Cell maximum measures force 5kg 11lb. You need to connect load cell with HX711 module like this, Red to E, Black to E-, Green to A, White to A-. Load Cell 4 leads, easy to use, plus 5-10V drive voltage, direct output as a voltage signal due to force changes. Works for arduino and raspberry pi. The HX711 On-chip active low noise PGA with selectable gain of 3264 and 128. This HX711 module uses 24 high precision AD converter chip hx711. It is a specially designed for the high precision electronic scale designwith two analog input channelthe internal integration of 128 times the programmable gain amplifier.

The 50kg load cell is a group of half-bridge strain gauge, there are 3 ways to use it. 2.Use two sensors to form a full-bridge measurement, measuring range for the sum of the two sensors 50kgx2 100kg. Use one load sensor 50kg with an external resistor to form a full-bridge measurement, the range of a sensor range 50kg. External resistance on the higher requirements.. Use two weight sensor 50kg to form a full-bridge measurement, measuring range for the sum of the two sensors 50kgx2 100kg. Use four weight scale 50kg to form a full-bridge measurement, measuring range for the sum of four sensors 50kgx4 200kg. If you have any problem, please contact seller as follow click DIYmallsyou can find Sold by DIYmalls under Buy Now button, in the new page, click Ask a question..

10,000 lbs x 2 lbs. Indicator includes Tare, Print, Hold, RS-232. Other capacities available.