Top 10 Best Max7219

MAX7219 LED Display Driver.

Dimension of Module 12.8X3.3X1.3cm5.04X1.3X0.51in. Operating voltage 5V. A single module can drive a 8x 8 dot matrix common cathode. 64 fixed screw holes with 3mm in its diameter. Equipped with input and output interfaces, support for multiple modules to cascade.

Resolution 32 x 8 LEDs. It is compatible with Raspberry Pi, Arduino and other development boards, and there are many examples of application cases on the Internet.. Including cable and additional pin header for easy expansion of the matrix. Package Includes2 x MAX7219 32x8 LED Matrix,2 x 5Pin header,2 x 5Pin female-to-female jump wire,2 x Velcro tape.

MAX7219 dip MAX package DIP MAX7219CNG MAX7219ENG.

Only three IO ports are used to drive the eight digit display. MAX7219 supports flicker free displays as well as cascading displays.. MAX7219 is an integrated serial input output common-cathode display driver, which connects your microprocessor to a 7-segment digital LED display with 8 digits.. This module is compatible with 5V and 3.3V microcontrollers.. VCC and GND should not be connected reversed, so as not to burn the chip. Compatible with Arduino.

MAX7219 is an integrated serial input output common-cathode display driver, which connects your microprocessor to a 7-segment digital LED display with 8 digits MAX7219 digital display control module, you can use it for Ar-duino.. The module is compatible of 5V 3.3V microcontroller Only three IO ports are used to drive the eight digit display.. Only three IO ports are used to drive the eight digit display. MAX7219 supports flicker free displays as well as cascading displays PCV board four corners of the fixed copper stud, which can effectively precent short circuit accidents happen.. Wiring instructions a program, for example, you can pick any IO port definition can be modified in the program VCC to 5V, GND to GND, DIN to P00, CLK to P02, CS to P01 Digital tube is 0.36 inch 4-bit integrated cathode digital tube Common cathode.. NoteVCC and GND do not reversed, it would burn the chip.51 MCU P0 port requires pull-up resistor, if your device does not have a pull-up resistor can be connected to other ports data lines..

Operating Voltage 5V. A single module can drive a 8x8 dot matrix common cathode. Dimensions 12.8X12.8X1.3 cm. Fixing screws with 64 holes with a diameter 3mm.

The MAX7219 is compact, serial inputoutput common-cathode display drivers that interface microprocessors Ps to 7-segment numeric LED displays of up to 8 digits, bar-graph displays, or 64 individual LEDs.. Included on-chip are a BCD code-B decoder, multiplex scan circuitry, segment and digit drivers, and an 8x8 static RAM that stores each digit.. Only one external resistor is required to set the segment current for all LEDs. A convenient 3-wire serial interface connects to all common Ps. Individual digits may be addressed and updated without rewriting the entire display.. The MAX7219 also allow the user to select code B decoding or no-decode for each digit.. The devices include a 150A low-power shutdown mode, analog and digital brightness control, a scan limit register that allows the user to display from 1 to 8 digits, and a test mode that forces all LEDs on..

The MAX7219 is an integrated serial inputoutput common-cathode display driver that connects a microprocessor to an 8-digit digital 7-segment LED display, or a bar graph display or 64 separate LEDs.br. It includes an on-chip B-type BCD encoder, multi-channel scan loop, segment word driver, and an 8x8 static RAM to store each data. Only one external register is used to set the segment current of each LED.br. A convenient four-wire serial interface can be connected to all common microprocessors. Each data can be addressed without any need to overwrite all displays when updating. The MAX7219 also allows the user to choose whether to encode or not encode each data.br. The entire device includes a 150A low-power shutdown mode, analog and digital brightness control, a scan limit register that allows the user to display 1-8 bits of data, and a detection mode that allows all LEDs to illuminate.br. There are three colors red, blue, and green The blue and green products are upgraded based on user feedbackbr.

1.Dimension of Module 12.8X3.3X1.3cm5.04X1.3X0.51in. 2.64 fixed screw holes with 3mm in its diameter. 3.A single module can drive a 8x 8 dot matrix common cathode. 4.Equipped with input and output interfaces, support for multiple modules to cascade. 5.MAX7219 Dot Matrix Module Green Light for Arduino Microcontroller 4 in 1 Display with 5pin Line.