Top 10 Best Raspberry Pi Motor Controller

L298N as main driver chip makes strong driving abilitysmall heatingstrong anti-interferencelow calorific value. Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability. Dual-channel H-bridge driver working mode creates higher working efficiency. To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage. Large capacity filter capacitance, afterflow protection diode, more stable and reliable.

This Motor Driver HAT gives your Raspberry Pi the ability to drive two DC motors, with drive current up to 2A.. Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards like Raspberry Pi ZeroZero WZero WH2B3B3B4B and later versions. Reserved I2C SPI control pins, allows to work with other control boards and sensors. Comes with an IR receiver for communication with an infrared remote controller.. Included 4x M2.520MM screws, 4 xM2.510MM copper pillars, 4x M2.5 Nuts. Easy to install on your RPi board. Please note Raspberry Pi board, remote control and motors in the photos are Not Included. Logic part input voltage 5V Driving part input voltage 4.8 24V .

Dual H-Bridge IC L293D. Motor Input Supply Range 6V - 24V. Single Motor Output Current 600mA or 1A peak per channel. On board Arrow Indicator for motor direction Indication,. 2 IR sensor connectors with 3.3V level output protection. Control 2 stepper motor.

This is a good parts kit for RC car project. It not only comes with 4pcs wheels and motors, but also 2pcs motor drive modules and 60pcs jumper wires, which are very useful accessories for your project.. Motor Drive Controller L298N used as the main driver chip. It has the strong driving ability, low calorific value and strong anti-interference ability.. TT Motor The motor is a two-axis motor with a reduction ratio of 148, which has strong anti-interference ability.. Smart Car Wheels The wheels are made of high-strength plastic and the tires are made of durable black rubber.. To avoid damage the voltage stabilizing chip of Motor Drive Module, please use an external 5V logic supply when using more than 12V driving voltage..

Dual-channel H-bridge driver working mode creates higher working efficiency,L298N as main chip, Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors.. To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.. Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability.. High working power to 46v,large current can reach 3A MAX and continue current is 2A, power to 25w.. Large capacity filter capacitance,afterflow protection diode, more stable and reliable..

Contains an I2C-controlled PWM driver with a built-in clock. It means, unlike the TLC5940 family, you do not need to continuously send it signals tying up your microcontroller it's completely free running. 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs, which is good when you want to control white or blue LEDs with a 3.4V forward voltage. Supports using only two pins to control 16 free-running PWM outputs you can even chain up 62 breakouts to control up to 992 PWM outputs.. 3 pin connectors in 4 groups, so you can plug in 16 servos at one time Servo plugs are slightly wider than 0.1 so you can only stack 4 adjacent ones on 0.1-hole female headers.. 12-bit resolution for each output - for servos, that means about 4us resolution at an update rate of 60Hz..

Widely Application The module is very suitable for DIY design car project, 3D printer, learning programming. This L298N Motor Driver Module is a high power motor driver module for driving DC and Stepper Motors. The module consists of an L298 motor driver IC and a 78M05 5V regulator. It uses an H-Bridge to easily control the direction and speed of up to 2 DC motors. The L298N used in this module is used as the driver chip, which has the characteristics of strong driving ability, low heat generation and strong anti-interference ability. The built-in 78M05 chip works by partially taking power from the drive power supply. If working with a drive voltage greater than 12V, please connect the external 5V logic power supply. Provide high-quality products and services, simple to use, including operation tutorials.

Note The Raspberry Pi and Servo in the photo are not included. User Manual Please get the link from the operation guide below. Note 1.If you only connect 5V power supply to USB interface, servo cannot be driven 2.You should connect higher power supply for higher-power servo 3.Make sure servo are connected properly, otherwise they will not move.. Servo Motor Driver You may have tried to control a robotic arm or a hexapod walker by using the Raspberry Pi, but finally get frustrated due to the limited number of PWM outputs and the jittering servo. Now you get a new option to bring your ideas to life, we prepare this useful Servo Driver Board for you.. Raspberry Pi connectivity, compatible with Raspberry Pi 4 3B 3B 2B 2B ZeroZero WZero WH and Jetson Nano.. I2C controlled, using only 2 pins Up to 16-Channel servoPWM outputs, 12-bit resolution for each channel 4096 scales Integrates 5V regulator, up to 3A output current, can be powered from battery through VIN terminal..

4 H-Bridges TB6612 chipset provides 1.2A per bridge with thermal shutdown protection, internal kickback protection diodes.. Up to 4 bi-directional DC motors with individual 8-bit speed selection so, about 0.5 resolution. Up to 2 stepper motors unipolar or bipolar with single coil, double coil, interleaved or micro-stepping.. Big terminal block connectors to easily hook up wires 18-26AWG and power.

L298N main driving chip, high drive ability, small heating value, strong anti-interference capability.. Dual H bridge DC stepper module, more stable and higher work efficiency.. Size 43 43 27 mm1.69 1.49 1.06in. With built-in 78M05 to supply power, to avoid the damage of voltage regulator chip, when the driving voltage is greater than 12V, please use the external 5V logic power supply.. Package 5 pcs L298N motor controller board module..