Top 10 Best Sony A7iv Cage

Improved Design 1. A cold shoe is added to the upper right corner of the cage to facilitate the installation of accessories such as Microphone 3468 and LED Video light 3286 2. Two 14-20 threaded holes with a spacing of 18mm are added at the bottom, which is compatible with SmallRig Quick Release Plate for Arca 3154. A QD hole is added at the bottom, which is compatible with QD quick release shoulder straps and other accessories.. For Sony A7R VA7 IVA7S IIIA1A7R IV SmallRig Cage 3667 is designed for Sony A7R V, A7 IV, A7S III, A1, A7R IV to facilitate low-angle shots and protect the camera while offering a wide range of accessory mounts. NOTE The HDMI Cable Clamp 3000 is not compatible with Alpha 1 and Alpha 7R IV because it will block the synchro terminal interface when used on the Alpha 7R V.. Multiple Mounting Points The cage has multiple 14-20 holes and 38-16 positioning holes for ARRI, which can attach accessories such as the upper handle 3765, the side handle 2093, and the monitor stand 2903B. There are 2 built-in cold shoe interfaces, which can install microphones, fill lights and other equipment the QD hole at the bottom is compatible with QD shoulder straps. Holes are reserved on both sides and bottom of the cage to attach Wrist Strap PAC2456 and Shoulder Strap PSC2428.. Three-Point Locking A positioning pin is added at the bottom of the cage, and the 14-20 screw and the left M2.5 screw form a three-point locking to make the camera stable. Adjust the direction of the left locking slider to adapt to different models, A7 IV side is suitable for Alpha 7 IV and Alpha 7R V, A7S IIIA1 side is suitable for Alpha 7S III Alpha 1 Alpha 7R IV. All-Round Protection Built-in all-round rubber gasket to prevent scratches. With the cage installed, the camera interface, dials, buttons and changing batteries are not affected. The opening and closing wrench design is added to the position of the battery compartment, which fits the curve of the fuselage more, solves the problem of placing the little finger, and enhances the grip of the fuselage.. Built-in Quick Release Plate The bottom quick release plate for Arca has added 14-20 holes with a spacing of 18mm, which is compatible for DJI RS 2 RSC 2 RS 3 RS 3 Pro, and can also be adapted to DJI RS 2 RSC 2 stabilizer mounting board riser plate and SmallRig Quick Release Plate for Arca 3154.. Power Backup Solution SmallRig NP-FZ100 camera battery charger set is available now, two 2040mAhReal rechargeable batteries and a charger brings long battery life for your videos and photos shooting, if you need a sufficient power supply, please search SmallRig NP-FZ100 Battery 3824.

CompatibilitySmallRig formfitting aluminum half cage 3639 is expecially designed for Alpha 7R VAlpha 7 IVAlpha 7S IIIAlpha 1Alpha 7R IV with lightweight protection of the camera.. Stable And Anti-twistIt includes two locking side plates and one 14-20 screw at the bottom to lock the camera and prevent deflection and gives access to dials and buttons while retaining the grip experience of a bare camera.. Multiple Mounting PointsThe half cage 3639 built-in all-around protective spacers protect the camera from being scratched. 14-20 threaded holes, 38-16 locating holes for ARRI, and cold shoes support top handle 2165, side handle 2093, monitor mount 2903, microphones, LED lights, etc. Quick release plate for Arca at the bottom is design for DJI RS 2 RSC 2 RS 3 RS 3 Pro and the quick release plate for DJI RS 2 RSC 2 RS 3 RS 3 Pro stabilizers for stabilizer shooting.. Built-In AccessoriesThis half cage 3639 stores a flat-head screwdriver and allen wrench that facilitates disassembly and assembly. The cage maintains rubber padding to prevent your camera from scratching and scuffing.. NoteHDMI Cable Clamp 3000 is not compatible with Alpha 1 and Alpha 7R IV cameras and will interfere with the synchroterminal interface when used on Alpha 7R V camera. To use the side lock, please remove the split ring on the left side of the camera first. Power Backup SolutionSmallRig NP-FZ100 camera battery charger set is available now, two 2040mAhReal rechargeable batteries and a charger brings long battery life for your videos and photos shooting, if you need a sufficient power supply, please search SmallRig NP-FZ100 Battery 3824.

For Alpha 7R VAlpha 7 IVAlpha 7 S III SmallRig Cage Kit 3669C includes a cage, a clamp for HDMI cable , a top handle and a side handgrip. It is designed to reduce armload and increase stability during handheld shooting while offering a wide range of accessory mounts. It is designed for Sony Alpha 7R V, Alpha 7 IV and for Sony Alpha 7 S III. Two-point Locking Mount the camera onto the cage with an integrated 14-20 screw, and use the two side locking platesone for Sony Alpha7S III, one for Alpha 7 IV to prevent twisting. To use the side locking plate, please remove the split ring on the left side of the camera first. Please note that the camera strap eyelet is occupied when using the side locking plate. All-round Protection Adopted aviation aluminium and formfitting design for security and durability. The Alpha 7 IV cage features built-in protective pads that prevent the camera from being scratched. It maintains access to the camera's controls and hot shoe and features when the camera mounted. Multiple Mounting Points The cage features one integrated shoe mount, multiple 14-20 threads and a 38-16 locating hole for ARRI. The cage also has a built-in NATO rail on the side, and it also features strap slots for a separately available neck or hand strap. A magnetic flat-head screwdriver Allen wrench is stored on the bottom of the cage to secure the mounting screw. Top handle Side handgrip Come with a top handle for low-angle shot and a side handle for increased stability. The top handle feels comfortable and enables easy carrying at a low-angle shot. The side grip features a silicone insert for better grip and more stable shooting.Handle features 14-20 threaded holes, 38-16 locating holes for ARRI, built-in cold shoes for mounting microphones, LED lights, monitors, etc.. Clamp for HDMI Cable The clamp for HDMI cable , mounted onto the left side of the cage via one 14-20 screw and two locating pins, prevents deflection and fixes cables with a thumbscrew to protect interfaces and ensure stable signal transmission. NOTEThis cable clamp is not compatible with Sony Alpha 1. Clamp for HDMI Cable interferes with the synchroterminal interface when used on the Alpha 7R V camera. Power Backup Solution SmallRig NP-FZ100 camera battery charger set is available now, two 2040mAhReal rechargeable batteries and a charger brings long battery life for your videos and photos shooting, if you need a sufficient power supply, please search SmallRig NP-FZ100 Battery 3824.

PROTECTIVE ARMOR for Sony a7 IV, a1, S3, R4, 73, R3, A9 Minimizes Wear Over Time. MOUNT ACCESSORIES via NATO Rail, Arri Compatible Rosette, Cold Shoe Receivers, 38-16 and 14-20 Threads with Locating Pins. COMPATIBLE with Type IVVI Side Handles Type IV Baseplates. CABLE SECURITY via HDMI Clamp and Male to Female HDMI Adapter. COMPACT NATO TOP HANDLE Provides More Flexibility When Operating and Handling.

FORMFITTING FULL CAGESmallRig A7S III Cage 2999 maintains access to the camera's controls and hot shoe. Made of premium aluminium alloy, the cage is a solid piece of metal that is highly resistant to oxidation and stands the test of time.. PERFECT PROTECTIONThe cage incorporates an anti-twist design with an M2.5 screw fixed to the strap hole in addition to the 14-20 camera mounting screw so your camera can't move around in the cage. SmallRig Cage 2999 also incorporates an anti-twist design with padding on the base to protect the camera from scratching.. MULTIPLE MOUNTING POINTSIn addition to one cold shoe mount and multiple 14-20 and 38-16 threaded holes, this formfitting aluminum cage features several ARRI-style mounts for preventing accessories from twisting when mounted on the cage. It also comes with a built-in NATO rail on the left of the cage. Mounting holes on the front allow mounting a separately available lens adapter 1764.. RECOMMENDATIONSThe cage is compatible with SmallRig universal accessory system. You can attach SmallRig Wooden Side Handle 2093 for hand-held shooting, and SmallRig Cable Clamp 3000 to protect the HDMI cable and port. ARRI-style mounts on the top and side are provided to attach SmallRig ARRI Locating Handle or SmallRig Ball Head Magic Arm.. SWEET DESIGNLightweight design with only 200g. Strap holes are included to add a separately available wrist strap or neck strap to your rig. Besides, with built-in magnetic suction design, the included Allen Wrench is ready to use without fear of loss.. Power Backup SolutionSmallRig NP-FZ100 camera battery charger set is available now, two 2040mAhReal rechargeable batteries and a charger brings long battery life for your videos and photos shooting, if you need a sufficient power supply, please search SmallRig NP-FZ100 Battery 3824.

This light weight cage is compatible with A7 III, II series to protect camera damaging. SD card slot, battery compartment, and all camera controls are accessed.. The built-in cold shoe on the top allows to attach articulating arm, EVF mount, Rode Video microphone, monitor, etc. Rosette at right side is provided to mount compatible with ARRI rosette handgrip for handheld shooting.. HDMI clamp in the upper left corner to organize your HDMI cable. HDMI lock mounting interface to protect the camera HDMI port. A NATO rail is at left side. It is designed to mount nato handle and other NATO compatible accessories quick release. The plate at the bottom of the cage enables you to attach an optional Raiser Block applicable arca swiss compatible with manfrotto plate.. This DSLR camera cheese top handle comes with standard cold shoe, which bases on the top to mount magic arm, camera monitor, flash light, led light, dslr microphone, wireless gear, EVF mount. Plenty of 14-20 and 38-16 threaded holes on the compact of the cage provide you a wide range of flexibility in attaching accessories such as microphone, monitor, sound recorders, top handle, EVF mount, tripod plate, cheese plate.. Made of aluminum alloy, durable and lightweight..

Specially designed cage for SONY A7S A7SII A7SM2 A7R A7RII A7M2 A7 II Cameras,the set is assembled by Camera Cage with 15mm Baseplate Rig and Top Handle,44 Carbon Fiber Matte Box,Follow Focus,LE Version Power Supply. Equipped with JTZlink, through JTZlink's top handle can achieve the Camera Video Start Stop Function. Only the Zoom,WT,Focus,REC buttons on the handles are available for Sony A7 A7R A7S Series Camera,Other buttons are unavailable,like IRIS. DP30 takes ALLinOne concept into its structure design, and this ensures all main modules of it compatible with almost all main cinema cameras, video dslr cameras, video mirrorless cameras on the market. With this cage, you only need to change the mounting plate to be compatible with other cameras. The customized mounting plates for Sony A9 A6000 A6300 A6300 A7A7RA7S III camera sold separately. The Top handle and 15mm baseplate rail rod rig are universal modules for JTZ Camera Cage,you just need to change the camera cage module for GH3 GH4 GH5 GH5s BMPCC Blackmagic Pocket FS5 cameras,the customized cage modules sold separately.

Compatible with Alpha 7R VAlpha 7 IVAlpha 7 S III Cage Kit 3668 includes a cage, a clamp for HDMI cable , and a top handle. It is designed to facilitate low-angle shots and protect the camera while offering a wide range of accessory mounts. It is designed for Sony Alpha 7R V, Alpha 7 IV and for Sony Alpha 7 S III. Two-point Locking Mount camera onto the A7 IV cage with an integrated 14-20 screw, and use the two side locking platesone for Sony Alpha7S IIIAlpha 1, one for Alpha 7 IV to prevent twisting. To use the side locking plate, please remove the split ring on the left side of the camera first. Please note that camera strap eyelet is occupied when using the side locking plate. All-round Protection Adopted aviation aluminum and formfitting design for security and durability. The Alpha 7 IV cage features built-in protective pads prevent the camera from being scratched. It maintains access to the camera's controls and hot shoe and features when camera mounted. Multiple Mounting Points The cage features one integrated shoe mount, multiple 14-20 threads and 38-16 locating hole for ARRI. The cage also has a built-in NATO rail on the side, and it also features strap slots for a separately available neck or hand strap. A magnetic flat-head screwdriver Allen wrench is stored on bottom of the cage to secure the mounting screw. Ergonomic Top handle The top handle feels comfortable and enables easy carrying and at a low-angle shot. It features 14-20 threaded holes, 38-16 locating for ARRI holes, built-in cold shoes for mounting other accessories like SmallRig monitor mount 2294. For HDMI Cable Clamp The clamp for HDMI cable, mounted onto the left side of the cage via one 14-20 screw and two locating pins, prevents deflection and fixes cables with a thumbscrew to protect interfaces and ensure stability signal transmission. Please note that this cable clamp is not compatible with Sony Alpha 1.The Clamp for HDMI Cable interferes with the synchroterminal interface when used on the Alpha 7R V camera. Power Backup Solution SmallRig NP-FZ100 camera battery charger set is available now, two 2040mAhReal rechargeable batteries and a charger brings long battery life for your videos and photos shooting, if you need a sufficient power supply, please search SmallRig NP-FZ100 Battery 3824.

FULL ACCESSIBILITYONLY FITS FOR SONY A7RIII A7III A7M3 Camera. The cage would not block any buttons on the camera and you are able to access not only the battery but even the SD card slot. The hot shoe is accessible for Sony XLR-K2MK1M. PERFECT PROTECTIONThe updated alpha A7RIIIA7III cage adds a second locking point on the right side to prevent from twisting. Two pieces of rubber cushion on the bottom that prevent the camera from scratching. MOUNTING POINTSAdd plenty of 14-20 and 38-16 threaded holes for attaching more accessories. Also features locating holes for ARRI standard and a cold shoe on the top to attach corresponding accessories. RECOMMENDATIONSIt could attach Monitor Mount BSE23462070 for the monitor. For ARRI locating points on the top are compatible with corresponding locating pins. 14''-20 threaded holes on the top could be mounted with Top Handle 19841638 for handheld shooting, or they could be mounted with EVF Support 1842 for better shooting. It could be mounted with HDMI Lock 36761679 to protect HDMI cable and cable port.. WHAT YOU GET1 x Sony A7RIII Cage 2087 Friendly 24-hour Customer Support, 30-day No-hassle Return Service, Worry-free 2-year Warranty.. Power Backup SolutionSmallRig NP-FZ100 camera battery charger set is available now, two 2040mAhReal rechargeable batteries and a charger brings long battery life for your videos and photos shooting, if you need a sufficient power supply, please search SmallRig NP-FZ100 Battery 3824.

PROTECTIVE ARMOR for Sony a7 IV, a1, S3, R4, 73, R3, A9 Minimizes Wear and Supports Accessories. MOUNT ACCESSORIES via NATO Rail, Arri Compatible Rosette, Cold Shoe Receivers, 38-16 and 14-20 Threads with Locating Pins. COMPACT NATO TOP HANDLE Provides More Flexibility When Operating and Handling. POWER RECORD via the Advanced Power Handle and Run Stop Cable. 15MM LWS BASEPLATE Supports Rod Based Accessories and Mounts to Tilta Dovetails.