Top 10 Best Stabilus 28052

PLACEMENT 17 inch 45Lbs200N gas shock struts compatible with Leer ARE SnugTop camper shell truck topper rear window, Truck Pickup Cab Canopy Door and other custom Applications.. PARAMETER Compressed Length9.9 252mm Center-to-Center Extended Length Center-to-Center17.1435mm , Force 45 Lbs Per Strut, two are 90LB.. NEED KNOW Please compare the length of your original gas spring' compression and extension, type of connector, and lift capability before purchasing.. INTERCHANGE NUMBER C16-04270. Easy to install, no special tools required. End Fiting 10mm Ball Stud Sockets.. INTERCHANGE NUMBER C16-04270. Easy to install, no special tools required. End Fiting 10mm Ball Stud Sockets..

CHECK LENGTHS AND PRESSURE BEFORE ORDERING. THESE DO NOT FIT ALL CANOPY and COVERS THE MEASUREMENTS ARE FROM CENTER OF BALL MOUNT TO CENTER OF BALL MOUNT, NOT FROM END TO END OF STRUT SEE PICTURE Use a measuring tape to measure the door gas strut that you are replacing. Measure from the CENTER of the gas prop head little plastic end, to the other side. DO NOT measure from the end of the gas prop, your measurement will be too long. Note that most applications allow for 1-5 size variation.. Truck Upfitters Pair of 45 pound each gas struts. 15.7 extended length and 9.4 compressed length. This size of door shock absorber is for medium height and weight rear or side camper shell doors. Each canopy shock has 45 lbs of pressure, for a total of 90 lbs of pressure. Please note that this does not mean that it can lift something that is 90 lbs. the typical hinged-style door weight for this prop is approximately 60-80 lbs, including the weight of the camper shell locks and keys.. These gas lift cylinders do not fit all camper shell brands models. Measure your strut from center of socket to center of socket when fully opened fully closed to get accurate measurement. Please see pictures to determine how to measure. Do NOT measure from end to end. Measurement must be from the center of plastic ball mount on each end of the gas spring lift. Measurement is important to ensure they open properly and get a good camper shell seal against the camper shell gasket when closed.. Comes with four 10mm ball mounts for alternate 'other than truck camper shell' applications, such as in camper canopy windoors, RV doors and awnings, boat hatch spring lifts, gas struts for cabinets, storage bed lifts, toolbox struts, etc. These gas shock lift supports CANNOT be compressed by hand. These gas props MUST be installed in the EXTENDED OPEN position. It is nearly impossible to install them in the CLOSED position. Please refer to the install video for guidance on how to install.. Equivalent to Suspa c16-23993 or Stabilus 14269. These camper shell shocks are compatible with many truck canopy types, including LEER truck cap parts, ARE truck topper parts, Glasstite parts, Century parts, Snugtop replacement parts Astro tops, ATC campers, and many other fiberglass brands that utilize gas shocks gas springs gas lift cylinders. Compatible with many gas lift brands, including stabilus, lift o mat, and Suspa. These are OEM quality and perfect fit for your topper.

Commonly used on RV entry doors. Replace your gas prop by matching its length and force as close as possible. One gas prop per package, 20 inch extended length, 10 lbs force. If there are 2 props, replace them both to keep door feet balanced.

15.71 inch 38Lbs169N Shocks Struts--A NEW PACKAGE will be offered if any quality defects occur. Welcome to Click Ask Seller Besides Your Order for In-time Assistance. 15.71 inch 38Lbs169N Window Struts--Compressed Length Center-to-Center 9.4in 239mm, Extended Length Center-to-Center 15.7in 399mm, Force 38 Lbs 169 N Per Strut. 15.71 inch 38Lbs169N Window Struts--Vepagoo gas shock struts fit for LeerARETonneau Camper shell rear window topper door Tonneau Cover lift supports RV Truck Car's window and so on.. 15.71 inch 38Lbs169N Window Struts---Interchange Part Number C16-09209. Easy to install, no special tools required.. 15.71 inch 38Lbs169N Window Struts--End Fiting 10mm Ball Stud Sockets.

CHECK LENGTHS AND PRESSURE BEFORE ORDERING. THESE DO NOT FIT ALL CANOPY and COVERS THE MEASUREMENTS ARE FROM CENTER OF BALL MOUNT TO CENTER OF BALL MOUNT, NOT FROM END TO END OF STRUT SEE PICTURE Use a measuring tape to measure the door gas strut that you are replacing. Measure from the CENTER of the gas prop head little plastic end, to the other side. DO NOT measure from the end of the gas prop, your measurement will be too long. Note that most applications allow for 1-5 size variation.. Truck Upfitters Pair of 45 pound each gas struts. 17.1 extended length and 9.9 compressed length. This size of door shock absorber is for tall medium weight rear or side camper shell doors. Each canopy shock has 45 lbs of pressure, for a total of 90 lbs of pressure. Please note that this does not mean that these gas lift shocks can lift something that is 90 lbs. the typical hinged-style door weight for this prop is approx 60-80 lbs, including the weight of the camper shell locks keys.. These gas lift cylinders do not fit all camper shell brands models. Measure your strut from center of socket to center of socket when fully opened fully closed to get accurate measurement. Please see pictures to determine how to measure. Do NOT measure from end to end. Measurement must be from the center of plastic ball mount on each end of the gas spring lift. Measurement is important to ensure they open properly and get a good camper shell seal against the camper shell gasket when closed.. Comes with four 10mm ball mounts for alternate 'other than truck camper shell' applications, such as in camper canopy windoors, RV doors and awnings, boat hatch spring lifts, gas struts for cabinets, storage bed lifts, toolbox struts, etc. These gas shock lift supports CANNOT be compressed by hand. These gas props MUST be installed in the EXTENDED OPEN position. It is nearly impossible to install them in the CLOSED position. Please refer to the install video for guidance on how to install.. Equivalent to Suspa C16-04270 or Stabilus 1822. These camper shell shocks are compatible with many truck canopy types, including LEER truck cap parts, ARE truck topper parts, Glasstite parts, Century parts, Snugtop replacement parts Astro tops, ATC campers, and many other fiberglass brands that utilize gas shocks gas springs gas lift cylinders. Compatible with many gas lift brands, including stabilus, lift o mat, and Suspa. These are OEM quality and perfect fit for your topper.

CHECK LENGTHS AND PRESSURE BEFORE ORDERING. THESE DO NOT FIT ALL CANOPY and COVERS THE MEASUREMENTS ARE FROM CENTER OF BALL MOUNT TO CENTER OF BALL MOUNT, NOT FROM END TO END OF STRUT SEE PICTURE Use a measuring tape to measure the door gas strut that you are replacing. Measure from the CENTER of the gas prop head little plastic end, to the other side. DO NOT measure from the end of the gas prop, your measurement will be too long. Note that most applications allow for 1-5 size variation.. Truck Upfitters Pair 2 total of 40 pound each gas struts. 12.2 extended length and 7.5 compressed length. This size of door shock absorber is for tall medium weight rear or side camper shell doors. Each canopy shock has 40 lbs of pressure, for a total of 80 lbs of pressure. Please note that this does not mean that it can lift something that is 80 lbs. the typical hinged-style door weight for this prop is approximately 50-70 lbs, including the weight of the camper shell locks and keys.. These gas lift cylinders do not fit all camper shell brands models. Measure your strut from center of socket to center of socket when fully opened fully closed to get accurate measurement. Please see pictures to determine how to measure. Do NOT measure from end to end. Measurement must be from the center of plastic ball mount on each end of the gas spring lift. Measurement is important to ensure they open properly and get a good camper shell seal against the camper shell gasket when closed.. Equivalent to Suspa C16-11028, Stabilus 19068, or Weatherguard 7009-2PK . Comes with four 10mm ball mounts for alternate 'other than truck camper shell' applications, such as in camper canopy windoors, RV doors awnings, boat hatch spring lifts, gas struts for cabinets, storage bed lifts, other toolbox struts, etc. These gas shock lift supports CAN'T be compressed by hand. They MUST be installed in the EXTENDED OPEN position. It is nearly impossible to install them in the CLOSED position.. NOT FOR STEEL TOOLBOXES- WILL NOT HOLD UP LID. Fit most Weatherguard ALUMINUM truck bed toolboxes ONLY, models 121-0-01, 121-5-01, 123-0-01, 123-5-01, 127-0-01, 127-5-01, 131-0-01, 131-5-01, 137-0-01, 137-5-01, 147-0-01, 147-5-01, 154-0-01, 154-5-01. Compatible with many truck canopy types, including LEER, ARE, Century, Snugtop, and ATC tops, many other brands that utilize gas shocks gas springs gas lifts. Compatible with many gas lift brands, including stabilus, lift o mat, Suspa..

Most used forC16-04154 14.45 inch 24Lbs107N gas shock strut compatible with 14''-15''19lb-26.5lbLeer ARE SnugTop camper shell truck topper rear window, Truck Pickup Cab Canopy Door, Cabinets Door and other custom Applications.. ParameterCompressed Length Center-to-Center14.45367mm, Extended Length Center-to-Center 8.98 228mm, Force 24 Lbs Per Strut, two are 48LB.. NotePlease compare the length of your original gas spring' compression and extension, type of connector, and lift capability before purchasing.. INTERCHANGE NUMBERC16-04145 C16-04145. Easy to install, no special tools required. End Fitting 10mm Sockets.. 121 MONTH REPLACEMENT SERVICEWelcome to Click Ask Seller BESIDE YOUR ORDER for In-time Assistance if any problem occurs..

CHECK LENGTHS AND PRESSURE BEFORE ORDERING. THESE DO NOT FIT ALL CANOPY and COVERS THE MEASUREMENTS ARE FROM CENTER OF BALL MOUNT TO CENTER OF BALL MOUNT, NOT FROM END TO END OF STRUT SEE PICTURE Use a measuring tape to measure the door gas strut that you are replacing. Measure from the CENTER of the gas prop head little plastic end, to the other side. DO NOT measure from the end of the gas prop, your measurement will be too long. Note that most applications allow for 1-5 size variation.. Truck Upfitters Pair 2 total of 24 pound each gas struts. 13.9 extended length and 8.9 compressed length. This size of door shock absorber is for short light weight rear or side camper shell doors. Each canopy shock has 24 lbs of pressure, for a total of 48 lbs of pressure. Please note that this does not mean that it can lift something that is 48 lbs. the typical hinged-style door weight for this prop is approximately 25-40 lbs, including the weight of the camper shell locks and keys.. These gas lift cylinders do not fit all truck capcamper shell brandsmodels. Measure your strut from center of socket to center of socket when fully opened fully closed to get accurate measurement. See pictures to determine how to measure. Do NOT measure from end to end. Measurement must be from the center of plastic ball mount on each end of the gas spring lift. Measurement is important to ensure they open properly and get a good camper shell seal against the camper shell gasket when closed.. Comes with four 10mm ball mounts for alternate 'other than truck camper shell' applications, such as in camper canopy windoors, RV doors and awnings, boat hatch spring lifts, gas struts for cabinets, storage bed lifts, toolbox struts, etc. These gas shock lift supports CANNOT be compressed by hand. These gas props MUST be installed in the EXTENDED OPEN position. It is nearly impossible to install them in the CLOSED position. Please refer to the install video for guidance on how to install.. Compatible w Suspa C16-06389 c16-21682, Stabilus 025647. These camper shell shocks are compatible with many truck canopy types, including LEER truck cap parts, ARE truck topper parts, Glasstite parts, Century parts, Snugtop replacement parts Astro tops, ATC campers, and many other fiberglass brands that utilize gas shocks gas springs gas lift cylinders. Compatible with many gas lift brands, including stabilus, lift o mat, and Suspa. These are OEM quality and perfect fit for your topper.

This listing includes 2 Lift Supports For the Liftgate.. Extended Length from Center Mount to Center Mount is 20.08 in.. High Quality Supports, designed to last, to OEM Standards.. Rust-resistant piston rod extends product life.. Compatible with the following OEM Numbers 014293,0317SS,15068721,15068722,15079252,15079253,15120902,15120903,16068721,3113PX,3127PY,4573,5788NO,612248,8196187,8317SS,8334SV,9925VO,RB8795154,SG330046.

APPLICATION 20 inch 150Lb Gas Shocks for RV King or Queen Size Bed Lift, Truck Tonneau Cover, Camper Window, Shed Window and other DIY applications such as Trap door, Heavy Duty Box lid.. PARAMETER Interchange Part Number C16-17566 C16-17566. Extended Length19.69in Compressed Length11.8in End Fittings10mm Nylon Ball Sockets. Force150 Lbs per shock. Mounting Hardware Needed 10MM Ball Stud Mounting Bracket. Not included in the package. NEED KNOW If you used these gas shocks as a replacement for the Truck Tonneau Cover or Trailer cover, you have to compare the length of your original gas spring' compression and extension, type of connector, and lift capability before purchasing.. TIPS 150lb Per strut, two are 300lb. SUPER STRONG You couldnt compress it by your hand Suitable for lids or doors weighing between 150lb and 250lb. 121 MONTH REPLACEMENT SERVICE Welcome to Click Ask Seller BESIDE YOUR ORDER for In-time Assistance if any problem occurs..