Top 10 Best Topping Pa3s

2xMA12070 Fully balanced Class D amplifier - Each channel of PA3s uses one MA12070 Class D power amplifier chip. This allows separation in layout improving performance and reducing crosstalk. The power is shared across two chips, the heat dissipation is also halved for each chip, improving reliability and extending the lifespan of the product. High output power - PA3s could output 80W x2 at 4ohm load, 10 THDN. In higher standard of THDN of 1, output power will be 65W x2 at 4ohm load. The output power is enough to drive any bookshelf speakers and even some floor speakers. Balanced Single -ended inputs - PA3s provides TRs balanced input and RCA single -end- ed input. The use of balanced input eliminates potential ground loop problems giving the pristinely clean audio without any hum.Two inputs are selectable using front panel button. P A3s will remember the input selected when it was turned off.. Comfort zone with lowest distortion - The lowest THDN of PA3s is in the range of 10-20W output, which happens to be the power range commonly used for listening to music. Everything is just in the rightcondition. Wider Use - With the help of a DAC, the function is expanded toa greater extent PA3s can be used with a DAC to expand the categories of digital inputs if used with a DACHPA, more comprehen- sive functions can be achieved..

Comfort zone with lowest distortion The lowest THDN of PA3s is in the range of 10-20W output, which happens to be the power range commonly used for listening to music. Everything is just in the right condition.. With the help of a DAC, the function is expanded to a greater extent PA3s can be used with a DAC to expand the categories of digital inputs if used with a DACHPA, more comprehen sive functions can be achieved.. Balanced Single- ended inputs PA3s provides TRS balanced input and RCA single end- ed input. The u use of balanced input eliminates potential ground loop problems giving the pristinely clean audio without any hum.. High output power PA3s could output 80W x2 at 4ohm load, 10 THDN. In higher standard of THDN of 1output power will be 65W x2 at 4ohm load. The output power is enough to drive any bookshelf speakers and even some floor speakers.. 2xMA12070 Fully balanced Class D amplifier Each channel of PA3s uses one MA12070 Class D power amplifier chip. This allows separation in layout improving performance and reducing crosstalk. The power is shared across two chips, the heat dissipation is also halved for each chip, improving reliability and extending the lifespan of the product..

MQA Full Decoder Products with a full MQA Decoder, like D90SE DAC, unfold the file to deliver the highest possible sound quality. At this level of playback you are hearing what the artists created in the studio - with precise file and platform specific DAC compensation and management.. Play back your music in higher quality The performance of D90SE has reached a new peak THDN 0.00005. Clearer details are at your fingertips.. Bluetooth 5.0 LDAC transmission D90SE has the certification of Hi-Res Audio Wireless and LDAC. It uses CSR8675 chipset to support L DACAACSBCAPTXAPTX LLAPTX HD protocol.. IIS input supports up to DSD1024 native When there is a better interface, you can use the HDMI cable to directly send the lIS signal into the D90SE's ESS9038PRO for better decoder. IIS input can support up to PCM32bit 768kHz DSD1024 native.. Coaxial, Optical and AES input support MQA full decoder D90SE not only support MQA input via USB, but all these inputs including UsB, coaxial, optical, AES can input MQA signal, which means you can hear more when playing MQA-CD..

Bluetooth 5.0 LDAC transmission DX3Pro has the certification of Hi-Res Audio Wireless and LDAC. It uses newest QCC5125 chipset to support LDACAACSBCAPTXAPTX LLAPTX HD protocol. To get even better sound quality from Bluetooth, we abandon the built-in DAC of QCC5125 and connect its digital signal to ES9038Q2M to decode.. NFCA circuit The new DX3 Pro has the NFCA circuit optimized for this unit, giving the ultra low noise and distortion. It pairs with high sensitivity IEMs and power hungry high impedance headphones nicely.. Pre-amplifier function Adapt to different usage scenarios, DX3 Pro has 4 output modes Headphone Amp, Headphone Amp Line out, DAC, and Pre amplifier.. PA3s is the best power amplifier for DX3 Pro PA3s has RCATRS balanced inputs. When used with DX3 Pro, the TRS balanced input can be used to input other audio sources. The output power of 80W x 24, 10THDN, 65W X 24, 1THDN can be adapted to most situations where speakers are used.. Bluetooth headphone amp Bluetooth DAC application Connect the Bluetooth of the phone, tablet or notebook to DX3 Pro, and connect the power amplifier, active speakers or headphones to the DX3 Pro's output, then DX3 Pro becomes your Bluetooth Headphone amp Bluetooth DAC. If your device supports LDAC transmission, you will get even better experience..

Dual ESS ES9038Q2M SABRE HIFI DAC Chips, MQA Full Decoding via USB. Support DSD512 Native and PCM 768kHz, MQA Full Decoding via USB. 2nd Generation 16 Core XMOS XU216, 4-PIN-XLR and 6.35mm Headphone Output. THDN as low as 0.00010, 1300mW X2 Output Power. DAC Pre amp applicaion Bluetooth receiverTablet and phone DAC application.

Bluetooth 5.0 LDAC Transmission DX3 Pro is equipped with new QCC5125 Bluetooth chip and supports audio encoding such as LDACAACSBCAPTXAPTX LLAPTX HD. The audio is transmitted Wirelessly and decoded using ES9038Q2M for better sound quality.. High Performance DAC CircuitES9038Q2M through meticulous engineering design and attention to details, DX3 Pro achieves 0.00015 THDN, completely and high-fidelity restore the sound quality of the studio.. Plug And Play, Turn PC Into a HIFI SourceDx3 Pro uses 2nd generation 8 core XMOS XU208, USB supports up to PCM32bit768kHz and DSD512 native. It also compatible with a variety of HIFI systems. And all inputs have achieved low Jitter, let listen to music more freely.. NFCA Circuit And Decoding Amp ApplicationDX3 Pro has a built-in NFCA headphone amplifier module tailored to it, providing low noise and distortion far superior to the industry. Connect the digital signal and earphone to DX3 Pro, it can be used as a decoder earphone, bringing you every detail of music.. DACPre-amplifier applicationDX3Pro has a simple Pre-amp function that you can use to adjust the volume. The digital volume adjustment will not has any imbalance between the left and right channels..

High-Resolution Audio - Mastertape-level decoding USB input up to 32bit768kHz DSD512 Coaxial input up to 24bit384kHz DoP128. Can be connected to your computerPClaptop, mobile devices like smartphonespadstablets via USB corresponding cables needed, and devices with coaxial output like digital transportsCD players.. Op-Amp Replaceable 7 Filter Modes - Everyone can be a tuner. The X8 18th Anniversary Edition is compatible with all kinds of dual op-amps. You can change the op-amp and search for the sound you like. Together with the 7 filter modes to select from, you can have so much fun exploring.. FPGA Technology - The X8 18th Anniversary Edition Uses the FPGA developed by aune to handle signals. Purer signals, purer sound.. Balanced TRS Preamp Output - Besides the inputs of USB, coaxial, optical and the outputs of RCA preampline, the X8 18th Anniversary Edition has now got the balanced TRS preamp out. Look what a compact device can provide.. High Spec Aesthetic Tuning - Actual measurements noise floor as low as 2.45V THDN as low as 0.00027 1kHz, 0.00020 18kHz. The professional and aesthetic tuning leads to the sound signature that is natural and full of musicality..

TRS Balanced Single-ended RCA inputs In addition to supporting various digital inputs, MX5 also supports fully balanced TRS and single-ended RCA analog inputs. Greatly expand the scope of application.. Merus Class D amplifier With the help of Infineon Merus Class D amplifer, MX5 can output 70W x2 under 4 ohm load 10 distortion, 55W x2 under 4 ohm load 1 distortion. Under 8 ohm load, 10 distortion can output 42W x2, and 1 distortion can output 35W x2, which can meet daily use.. NFCA Headphone Amplifier The MX5 has the NFCA circuit optimized for this unit, giving the ultra low noise and distortion. It pairs with high sensitivity IEMs and power hungry high impedance headphones nicely. The built-in headphone amp allows you to enjoy music by yourself without disturbing others.. Built-in EQ function, now you can adjust treble and bass MX5 supports users to adjust the treble and bass. The treble and bass provide adjustable ranges from -10dB to 0dB respectively.. 2 step gain settings for both power amplifier headphone amplifier In order to adapt to input signals with different strengths, MX5 provides two step gain settings for both power amplifier and headphone amplifier. The gain can be set on the remote control..